Re: Mark's 1950 Super Eight
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Can you share the name of the company that you worked with for the OD cable? Mine, like most of my cables, is frozen and although I have not attempted to break it loose, I would like to be prepared.
Thank you!
Posted on: 2018/11/5 11:03
|
|||
1948 Packard 2262 Deluxe Eight Touring Sedan ? "Clara Belle"
1964 Rambler Classic 550 ? "Ramona" Wishlist: 1939 Graham Spirit of Motion, Shark nose |
||||
|
Re: Mark's 1950 Super Eight
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Sure:
Cable Craft 4401 South Orchard Street Tacoma, Washington 98411 Phone: 253 475-1080 Fax 253 474-1623 https://www.cablecraft.com/
Posted on: 2018/11/5 11:33
|
|||
|
Re: Mark's 1950 Super Eight
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Today I finished the rewiring of the 50. What a job, I did it without taking out the dash finding it very relaxing working on my back feet up in the air on the seat. I worked a little at a time when I got tired I quit. Part time it took me about 3 weeks to complete.
Lessons learned... Remove the heater distribution box from the heater and firewall. As others have said drop the heater controls. Remove the two hidden special nuts holding the switches to the front fascia. Disconnect the cigar lighter, the nameplate illumination light, and the Headlight indicator light from the switch panel. Now you can pull the switches back from the from the fascia. Remove the radio next. It is easier to work underneath when the radio is out. Remove the front fascia. To do this there are two flat head bolts over the ash tray and one over the hole that the radio fits into. Next remove the one Phillips bolt under the radio that holds the bottom of the dash to the face plate. Next remove the small Phillips screw that holds the bottom of the ash tray opening to the dash. The headlight on light is attached here. Lastly, notice that there are two very small Phillips screws at the top of the radio grille opening. These hold the face plate to the dash. There is a metal bar in the opening that the ash tray rocks on. You may have to work that out before the face plate will come out. Carefully work the face plate out of the opening. Now you have a way to get your arm into the space behind the instruments. Remove the nuts holding the harness to the instruments. Carefully disconnect the switch panel from the harness. At this point I cut out the harness severing it at the firewall as I was not going to reuse it. I worked out the harness through the opening I had created by removing the switch panel. I took the old harness indoors and cut it apart as I used the wires that were only behind the dash as patterns for the new wires. Using the wiring diagrams from this site I duplicated the harness carefully labeling each wire on each end with the numbers from the diagram. I did that as it is impossible to get all of the proper colors in cloth covered wire and I wanted to use cloth covered wire for period correctness. I cut the wires that pass through the firewall long and cut and attached them once the under dash work was done. Before I buttoned up the dash I checked each circuit with power to ensure things were right. Good thing too, as when I rewired the turn signal to switch socket I misread the diagram ans wired it from the rear and not the front, so nothing worked right. I had to open up the socket and solder the connections correctly, now it works right. Finally, I tied up all the wiring using tie wraps and reinstalled the components in reverse order. Ran the car for the first time in a month today and everything works as it should.
Posted on: 2018/12/3 19:53
|
|||
|
Re: Mark's 1950 Super Eight
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
September 1st. The Packard made it to the wedding of my oldest, Sam and his beautiful bride Chloe. I worked my tail off to get the car in shape for a cross town trip and everything worked as planned...here's the picture taken at the reception.
Posted on: 2018/12/26 14:06
|
|||
|
Re: Mark's 1950 Super Eight
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Congratulations on finishing the hard work to deliver a good looking properly performing and well mannered car and providing quality transportation for a son and new daughter in law that undoubtedly appreciated it.
Posted on: 2018/12/26 14:22
|
|||
Howard
|
||||
|
Re: Mark's 1950 Super Eight
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Mark (50 2382), as a matter of course the bride is the main attraction but the black & white / white & black combination of car and groom is also well worth seeing.
Posted on: 2018/12/26 16:31
|
|||
The story of ZIS-110, ZIS-115, ZIL-111 & Chaika GAZ-13 on www.guscha.de
|
||||
|
Re: Mark's 1950 Super Eight
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Well, I finished the new seat upholstery today. This was a job that I found took way too long but was extremely rewarding. I stumbled across an industrial sewing machine for cheap and that is what got me started. The project took about 6 weeks of spare time and a couple of weekends. I was not too tough and I learned how to sew along the way. I started with the easiest cushion and work my way up to the hardest. I used the old seat upholstery as patterns. The front seat support turned out to be the hardest. The finished product looks great.
Now on to driving instead of working.
Posted on: 2019/5/23 16:46
|
|||
|
Re: Mark's 1950 Super Eight
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Great job - Thanks !
Posted on: 2020/11/21 1:05
|
|||
|
Re: Mark's 1950 Super Eight
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Fine job! There are a lot of 22nd-23rd Series Packards out there that could benefit from your upholstery expertise.
Steve
Posted on: 2020/11/21 10:23
|
|||
.....epigram time.....
Proud 1953 Clipper Deluxe owner. Thinking about my next Packard, want a Clipper Deluxe Eight, manual shift with overdrive. |
||||
|