Re: 1937 120 Trunk Shelf
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
The shelf that my 1940s had was plywood but coated and sealed black in some protective material like creosote but without the smell.
Posted on: 2020/7/24 10:58
|
|||
|
Re: 1937 120 Trunk Shelf
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
One piece of plywood, painted black, with a rubber mat as shown. Let me know if you need more pictures.
Posted on: 2020/7/24 11:02
|
|||
1937 120 1092 - Original survivor for driving and continued preservation. Project blog / Registry
1937 115 1082 - Total basket case, partial restoration, sold Hershey 2015 Project blog / Registry |
||||
|
Re: 1937 120 Trunk Shelf
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I believe that Exterior and Marine plywood use the same glue, but that Marine is supposed to be free of voids in the layers (in actuality it has fewer but not zero in the inner layers).
Posted on: 2020/7/24 11:15
|
|||
|
Re: 1937 120 Trunk Shelf
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
These pictures are wonderful and I don't think I need anything else. I now have a plan in place to construct my shelf. Thanks to everyone for your help.
Posted on: 2020/7/24 15:13
|
|||
Roger Howe
Whitewright, TX 1937 120C Touring Sedan |
||||
|
Re: 1937 120 Trunk Shelf
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Roger, any good auto trim shop should be able to provide you with material for a rubber mat, or cut one for you.
Posted on: 2020/7/25 15:07
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: 1937 120 Trunk Shelf
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks and now that I am getting a template from Mike in Tucson, obtaining the rubber mat should be a breeze.
Thanks to everyone for your help.
Posted on: 2020/7/25 18:29
|
|||
Roger Howe
Whitewright, TX 1937 120C Touring Sedan |
||||
|
Re: 1937 120 Trunk Shelf
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Hi. Yes, I have looked that there are multiple locations nearby where I can obtain Baltic Birch plywood, but my question now is what is the "correct thickness?" I can get it in either 1/2" or 3/4". The pictures send earlier appear to show something in the 3/4" range. What does your documentation show?
Thanks, again and again.
Posted on: 2020/7/26 11:25
|
|||
Roger Howe
Whitewright, TX 1937 120C Touring Sedan |
||||
|
Re: 1937 120 Trunk Shelf
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
1/2" plywood.
I also noticed when I was measuring it this morning that the back edge is rounded. I hadn't noticed that little detail before. You can see the rounding in the first picture I posted previously. If you need a closer picture showing the profile, just let me know.
Posted on: 2020/7/27 7:44
|
|||
1937 120 1092 - Original survivor for driving and continued preservation. Project blog / Registry
1937 115 1082 - Total basket case, partial restoration, sold Hershey 2015 Project blog / Registry |
||||
|
Re: 1937 120 Trunk Shelf
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks, Ken. Now, when you say "rounded", do you mean that the corners are rounded off and not square or is the edge on the top and bottom of the piece rounded to prevent snags somewhere? What I mean by that is if you look at the piece from one of the ends you would see the back edge appearing to be more of less a semi-circle. I hope I've explained this sufficiently.
Posted on: 2020/7/27 9:05
|
|||
Roger Howe
Whitewright, TX 1937 120C Touring Sedan |
||||
|