Merry Christmas and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
39 user(s) are online (37 user(s) are browsing Forums)

Members: 0
Guests: 39

more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



« 1 ... 48 49 50 (51) 52 53 54 ... 156 »

Re: KPack's 1954 Panama
Home away from home
Home away from home

Tobs
See User information
Hi Kevin,
Great addition that blast cabinet. It is nice to see parts go from rusty and crusty to bare metal, then to shiny paint. It will help you a lot with getting things looking nice.

I had the same problem with my "hot air choke tube" I just ran a new metal tube to the top of the hole on the manifold, reduced the diameter of the end of the tube and jammed it in the broken off tube, and put some exhaust sealer putty around it. It is a pragmatic fix, but works. -I think there are pics in my blog from a few years ago. Drilling out that old tube and then pressing a new one into the manifold is going to be a lot of work, and I would not do it.

Posted on: 2021/1/7 5:11
1953 Clipper Delux Club Sedan, 1953 Caribbean, 1969 912, 1990 Miata
 Top  Print   
 


Re: KPack's 1954 Panama
Home away from home
Home away from home

Ross
See User information
The heat riser tube is only inserted into the manifold a very short distance. There is a labyrinth cast there. Just drill it with a 1/4" drill bit--that will take about 3 seconds. If you start bringing cast iron dust you are going too far. You would have to really try to damage anything.

Posted on: 2021/1/7 9:40
 Top  Print   
 


Re: KPack's 1954 Panama
Home away from home
Home away from home

kevinpackard
See User information
Thanks both of you for the suggestions. Ross, are you saying use the 1/4" bit to open up the center of the tube and not remove all of it? So I should make a tapered fit like Mike did? Seems like 1/4" would be too small to remove all the remnants of the tube, which is why I ask.

While I'm on the subject, what diameter is the original tube? I'll need to find something I can use at NAPA.

-Kevin

Posted on: 2021/1/7 11:00
 Top  Print   
 


Re: KPack's 1954 Panama
Home away from home
Home away from home

Ross
See User information
Use a 1/4" bit as it is a 1/4" tube.

Posted on: 2021/1/7 13:23
 Top  Print   
 


Re: KPack's 1954 Panama
Home away from home
Home away from home

Tobs
See User information
Exactly, I just went out and measured mine...As Ross wrote, it is a 1/4 inch tube. The end of the tube that goes into the carb is flared, you can flare the tube yourself if you have the equipment, or buy a lenght of tube from Napa and cut to fit.

Posted on: 2021/1/7 13:31
1953 Clipper Delux Club Sedan, 1953 Caribbean, 1969 912, 1990 Miata
 Top  Print   
 


Re: KPack's 1954 Panama
Home away from home
Home away from home

kevinpackard
See User information
Well that was a nice easy job. Ross was right...though it took me closer to 10 seconds. 1/4" drill bit straight down. Really easy to tell if you're drilling the steel or touching the iron. Going to grab a piece of tubing from NAPA tomorrow, then bend, cut and install. Waiting for a replacement choke thermostat (replacement carb's choke thermostat housing is falling apart) then the new carb goes on.

Thanks for the help!

Attach file:



jpg  (122.72 KB)
1059_5ff7e9dc0cc6b.jpg 768X1024 px

Posted on: 2021/1/8 0:13
 Top  Print   
 


Re: KPack's 1954 Panama
Home away from home
Home away from home

Tobs
See User information
Great work! glad you brought this up, now I will have to drill mine out and make a better repair than what I have. I didn't know that the tube was just stuck in a little bit.

Posted on: 2021/1/8 8:57
1953 Clipper Delux Club Sedan, 1953 Caribbean, 1969 912, 1990 Miata
 Top  Print   
 


Re: KPack
Home away from home
Home away from home

kevinpackard
See User information
Some progress on the Panama over the past week. I've been getting things ready for eventually getting a new windshield installed. As part of that process I am doing a bit of body work on the strip right above the windshield flange and below the drip rail to smooth it out and make it as nice as possible. I also removed all the old seam sealer from the drip rail. Most of it had surface rust underneath it that was bleeding through the white paint. With it out the way I used a wire brush on a Dremel and cleaned it as best I could. Then applied some Ospho with a small brush and let it sit for a day. Reapplied Ospho and immediately cleaned it off with water (supposed to be the only way that you can get the acid off). Then mixed up some epoxy primer and painted it into the seam. I'll apply new seam sealer soon.

Fabric samples came from SMS. They are very good. The seat fabric is right on. My original fabric is definitely faded. The headliner sample they sent is not correct though. The original headliner (confirmed with other Panama's) is smooth, like the center sample. Compared to the scraps of the original that I have left, it looks like a good match. So the headliner is now being made and should hopefully be here in a couple weeks. Now I have to learn how to install a headliner.

I had previously wire wheeled, applied Ospho, and primed all the headliner bows. I went back and scuffed them up and painted them with a gray enamel (easier to see against the black when installing) and put them back in place to test the fit. All good.

It's amazing to see the difference on the roof from when I first got the car. 6 months ago I pulled down the original headliner to reveal a disaster. Now I'm getting ready to install a new one, and the roof is rust-free, epoxied, painted, insulated, and clean. Too bad it will never be seen again.

I took the lower interior windshield trim and cleaned it up. This was another of the pieces that had been covered in fake wood vinyl sticker at some point in the past. I'm glad it was because it kept the chrome almost pristine. Removing all the glue gunk was a pain, but they polished up very nicely.

This next week I will finish the body work above the windshield, seam seal the drip rail, and learn all about headliners.


-Kevin

Attach file:



jpg  1059_600665b8c3266.jpg (66.19 KB)
1059_600665b8c3266.jpg 1024X768 px

jpg  1059_600665d4b3195.jpg (113.03 KB)
1059_600665d4b3195.jpg 768X1024 px

jpg  1059_600665edbaa32.jpg (100.48 KB)
1059_600665edbaa32.jpg 1024X768 px

jpg  1059_600666086deae.jpg (125.72 KB)
1059_600666086deae.jpg 1024X768 px

jpg  1059_6006663b3d9cd.jpg (119.46 KB)
1059_6006663b3d9cd.jpg 1024X768 px

jpg  1059_6006667a221d5.jpg (140.79 KB)
1059_6006667a221d5.jpg 1024X768 px

jpg  1059_6006669bbe2f1.jpg (178.90 KB)
1059_6006669bbe2f1.jpg 1024X768 px

jpg  1059_600666e48dec3.jpg (75.36 KB)
1059_600666e48dec3.jpg 1024X683 px

jpg  1059_6006670465d83.jpg (102.38 KB)
1059_6006670465d83.jpg 1024X768 px

Posted on: 2021/1/17 19:59
 Top  Print   
 


Re: KPack's 1954 Panama
Home away from home
Home away from home

kevinpackard
See User information
Alright, got the photos up from before. They lost their file names though. No big deal though.

Had some time to work today, and I focused on the replacement carb I picked up from Ross. I had previously completely disassembled it and cleaned every component. It already been rebuilt at some point in the past, and those rebuild components were still in good condition. The threads on the heat riser tub were cross-threaded, so I corrected that. Then removed the original carb and installed the new one. Put some fuel in the float bowl and car started right up. However, it was somewhat rough, and died after a few minutes. Started it up again, was a bit better, but then died again. Tons of smoke, no oil smell...just super rich.

After it died the second time I saw that there was gas dripping out from the throttle plate shaft bushing. Looking down the throat showed that it was super wet inside the carb. My guess is the float either has a hole, or the needle and seat are bad.

I knew that the original carb worked, and it had brand new rebuild parts on it. So I opened them both up and swapped the float and needle/seat from the original carb into the new carb. Reassembled everything and installed the new carb back into the car. Car started right up and seems to work fine. The choke plate opens up slowly when getting warm, though never reached fully open. Not sure how this normally acts. Accelerator pump seems to work better.

I noticed that the car has a hard time returning to normal idle after taking my foot off the gas. It did this before I swapped carbs. I have to manually move the gas pedal to get the idle back to normal....it sticks high. Problem in the throttle linkage? Sticking pedal? Should I lube the throttle plate shaft on the carb?

-Kevin

Posted on: 2021/1/19 0:09
 Top  Print   
 


Re: KPack's 1954 Panama
Home away from home
Home away from home

r1lark
See User information
Kevin, in general, the steps I take with a sticking throttle would be as follows:
1) Compare your linkage setup to the parts manual - do you have all the correct pieces? Especially verify that you have the correct return springs and that they are connected in the correct locations. I always stay away from aftermarket return springs -- get NOS ones or good used. Are all the little clips that the springs anchor to in place?
2) Disconnect the linkage from the carb, and make sure the various linkage on the carb itself works freely.
3) With the linkage still disconnected from the carb, see if the rest of the linkage works freely. If it doesn't, one by one disconnect each linkage piece to see if the binding frees up. Go all the way back to the pedal. Check all the joints for wear, signs of binding, etc. Repair/replace as required.
4) Is the linkage rubbing on something that it shouldn't be rubbing on - non-stock parts, engine not in correct location due to bad engine/trans insulators, etc?
5) Properly lube and replace all components.
6) Perform any linkage adjustments per the Shop Manual

I'm sure that Ross and others that have specific experience with '54s will chime in here. There may be common wear issues or even design issues that were later addressed with Service Letters. Unfortunately, I don't have much experience with Packards (yet!), but just tried to lay out how I would generally troubleshoot a sticking linkage issue.

Keep us informed on what you find!

Posted on: 2021/1/19 8:30
Paul
www.studebakerskytop.com
 Top  Print   
 




« 1 ... 48 49 50 (51) 52 53 54 ... 156 »





- The following Google Ad-Sense Advert helps fund the cost of providing this free resource -
- Logged in users will not see these. Please Join and Donate to help support the website -
Search
Recent Photos
Photo of the Day
Recent Registry
Upcoming Events
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved