Re: 37 Packard 120 rear window question
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Very likely as it needs a solid, smooth seal in that area so that should be properly repaired.
Posted on: 2023/6/6 16:54
|
|||
|
Re: 37 Packard 120 rear window question
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Yeah that's what I was thinking but I figured I would ask other opinions on this matter.
Posted on: 2023/6/7 9:13
|
|||
Follow us on Instagram & TikTok @metal_edge_creations
|
||||
|
Re: 37 Packard 120 rear window question
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Stupid question...did it leak before? If the gasket seats past the hole area then the hole does not come into play. Very likely though, if there is a hole there is a leak. Next decision is how to fill it? I think I see wood around the opening so a good fibreglas filler on clean metal will seal the hole as it is not structural in carrying a load, it will need to withstand the window gasket reassembly so you will need to look hard at how much metal is there now and will it take the load of installing the gasket rubber without flexing and potentially cracking the filled spot. Replacing with metal is best but having help with lots of wet rags to keep the wood from charring is going to be needed. Had to do it on a Model A and took a couple of volunteers in cramped quarters to get'er done, and most of a case of beer afterward!
Bob J.
Posted on: 2023/6/7 10:29
|
|||
|
Re: 37 Packard 120 rear window question
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Good afternoon...Sounds about right! Ernie in Arizona
Posted on: 2023/6/7 16:49
|
|||
Caretaker of the 1949-288 Deluxe Touring Sedan
'Miss Prudence' and the 1931 Model A Ford Tudor 'Miss Princess' ![]() |
||||
|
Re: 37 Packard 120 rear window question
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
I'm not sure if it leaked before. What it looks like with the new seal laid in there it may possibly leak. The owner is stopping by tomorrow to see it for himself.
Posted on: 2023/6/8 8:55
|
|||
Follow us on Instagram & TikTok @metal_edge_creations
|
||||
|
Re: 37 Packard 120 rear window question
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
I'm going through the bag marked "rear window vent parts" for this car and I'm having a hard time figuring out where this part goes. Does anyone know where this clip is installed?
Posted on: 2023/6/8 8:59
|
|||
Follow us on Instagram & TikTok @metal_edge_creations
|
||||
|
Re: 37 Packard 120 rear window question
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
It looks like, the one which holds the wiring harness as it comes up from the left side for the instruments, that is bolted to the left side upper hinge bolt.
One of the three bolts, that hold the door hinge. Depending on size it could be the one one the left(drivers)side at the spot Where the front body mounting bolt is,and used for again the wiring harness exit.
Posted on: 2023/6/8 10:01
|
|||
|
Re: 37 Packard 120 rear window question
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Thanks for this info, it helped big time! Yeah not even close to the vent windows
![]()
Posted on: 2023/6/8 15:30
|
|||
Follow us on Instagram & TikTok @metal_edge_creations
|
||||
|