Re: New Windows but I broke the Door Lock Button - How do I fix?
|
||||
---|---|---|---|---|
Forum Ambassador
|
The door panel is not terribly hard to remove. It is held on by spring clips which push into holes in door. Don't remember on a Clipper if lock button goes thru molding or is on face of door panel but since yours broken, one less thing to worry about removing. There may be a screw or two down low if someone has been there before so look for any and remove.
Start by removing the screws around inside window molding and remove. On some windows, the molding is actually behind a clip so once the screws removed, the molding has to be pulled down slightly and then out to clear the clip. The door and window handles are held on by pins thru their respective shaft and handle. Somewhere fairly close to each handle, push panel in very hard against a spring--maybe half inch or so-- until you see the pin and then push pin out with a punch or awl. After handles removed, use a sturdy and fairly wide but thin flat bar around the edge of panel and pry clips out of door. There are several on each edge maybe 8-10 inches apart. The clips may be rusted and may break. Replacements are available from restoration specialties. The old door panel is a different story and a narrow tool may tear the clips out of the board material so go slowly and be careful. Once all the clips are loose, panel can be lifted up off the arm rest bracket and removed. Don't think you have power windows, but if so, then 3 wires will have to be disconnected from switch before panel can be taken away. The lock mechanism is attached to the knob by a rod which essentially moves a lever up and down. You should be able to see what the problem is once panel is removed.
Posted on: 2009/5/21 10:02
|
|||
|
Re: New Windows but I broke the Door Lock Button - How do I fix?
|
||||
---|---|---|---|---|
Home away from home
|
It is hard to take off a door panel without damaging it, unless you have a special tool.
The special tool is made of a 2 1/2 or 3" wide scraper or putty knife. You take the scraper and grind a notch in the middle about 1/4" deep and 1/4" wide. Now you can slide the tool under the door panel and feel around for the clip. Get the clip in the notch and pry it out. One of those gadgets you use to pry dandelions out of your lawn may work as well but I haven't tried it.
Posted on: 2009/5/21 11:10
|
|||
|
Re: New Windows but I broke the Door Lock Button - How do I fix?
|
||||
---|---|---|---|---|
Webmaster
|
Frank,
The recommend way to pull the door panels of is this. 1) Remove the lock knob: On the 51-54 Clippers you remove the plastic lock knob from it's shaft using a heat gun to soften the plastic so it will slip off the shaft. Packard used some Rube-Goldberg type heating device to do this. 2) Remove the window reveal (garnish moulding) . Loosen the screws that hold the reveal in place, and remove it. 3) Remove the window, and door handle cranks 4) Pop the panel loose. They make specific tools for popping those clips, but I find a wide bladed putty knife (or spackling knife) works great also. To reinstall, just reverse the order. Possibly the lock mechanism need to be lubricated and worked back and forth. Also make sure the lock linkage rods are not binding on anything. You have to do all of this because the Window Reveal over laps the top of the door panel by a couple of inches. You may be able to wiggle the panel out, but then risk damaging the panel. But you cant remove the Window Reveal without removing the plastic lock knob. The knob is press fit onto the shaft, so that is the reason you have to heat it soften the plastic enough to pull it loose.
Posted on: 2009/5/21 12:27
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Re: New Windows but I broke the Door Lock Button - How do I fix?
|
||||
---|---|---|---|---|
Home away from home
|
I usually use either the claw end of a hammer or the flat part of a nail puller bar. Just about anything suggested here or above will work just fine with a little patience.
Posted on: 2009/5/21 21:48
|
|||
|
Re: New Windows but I broke the Door Lock Button - How do I fix?
|
||||
---|---|---|---|---|
Home away from home
|
HH/Rusty/Kev/Chuck - thanks for all of the great advice on this. The glass shop owner (Galvin Glass in Bellevue, Ne) is a great guy. He said just bring it back to him and he would take the panel off and get the knob fixed (no charge). Between your notes and my watching him closely, I'm gonna figure this out. This is important because down the road, I may want to take all the panels off and bring them into an upholstery shop and get them restored. I may be wrong but I think it may be able to get a better price if I bring them in already off the car ready to be worked on. Again - thanks for the advice and have a great Memorial Day Weekend.
Posted on: 2009/5/22 14:56
|
|||
|