'56 Torque Convertor Removal
|
||||
---|---|---|---|---|
Webmaster
![]() ![]() ![]() |
So the gentleman that is bringing the '56 transmission to me from Northern Calif called, and reported that he can't get the convertor loose from the fly wheel.
The motor and tranny are out of the car, and are already separated, but the conveyor is still on flywheel. He said motor has sat outside for awhile in the elements. He has removed the 4 bolts that hold that convertor to the fly wheel, but it still won't come loose. Are there any other fasteners, or is just rust holding them together at this point? Need to call him back before he take a sledgehammer to it.
Posted on: 2012/1/3 14:31
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Re: '56 Torque Convertor Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Just tell him to bring u engine trans and all if it's cheap enuf. IF engine is a SCRAPPER and noone cares about the crank then remove engine oil pan and pull the entire unit crank flywheel and TQ and all.
Last ditch effort (if junk creank) then strike the FRONT END of the crank shaft (where harmonic balancer fits) with a sledge hammer. BUt use that as ONLY a last ditch effort. Mite have to JUDICOUSLY pry the TQ away from flex plate. I'd rather just get the entire crank and TQ as one piece and then worry about it later or better yet the entire engine.
Posted on: 2012/1/3 14:57
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: '56 Torque Convertor Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Be nice to see oil pump too.
Posted on: 2012/1/3 15:19
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: '56 Torque Convertor Removal
|
||||
---|---|---|---|---|
Webmaster
![]() ![]() ![]() |
Keith, only interested in the Transmission as nothing else is applicable to my '54 motor. Plus I think he is selling the motor seperately.
Howard, thanks for the info and pictures.. He is soaking the hell out of it right now with penetrating oil. He has till Friday night to break it loose before he drives down from Santa Maria with it.
Posted on: 2012/1/3 17:16
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Re: '56 Torque Convertor Removal
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Go to Home Depot or Lowes and buy a bundle of wood shims, the kind they use for door jambs. Drive the shims between the flywheel and the TC. A little at a time and that will also give you some room to spray PB Blaster in there. It has to be rusted together. Even better if you can turn the crank and work your way around.
Posted on: 2012/1/3 20:14
|
|||
|
Re: '56 Torque Convertor Removal
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Actually, it is stuck in the crankshaft. I just thought about that. Can't be stuck on the flywheel or flexplate.
Posted on: 2012/1/4 2:24
|
|||
|