Merry Christmas and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
142 user(s) are online (137 user(s) are browsing Forums)

Members: 0
Guests: 142

more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



(1) 2 »

Troubleshoot Loud Ticking 2498 288 Ultramatic
#1
Home away from home
Home away from home

kunzea
See User information
I can't figure out loud ticking.

2498 288 Ultramatic. I finished the following on the engine:

valve seats ground
valves ground
valve guides reamed to where every valve would bounce when dropped

head sandblasted and surface measured within spec
head sandblasted, primed and top coat
replaced cracked intake manifold
intake and exhaust manifolds sandblasted, primed and painted
intake/exhaust manifold assembly resurfaced

New head and manifold gaskets

New grade 5 or 8 washers and nuts for head and manifolds.

Cranked engine. Engine had some valve noise but not excessive.

Drove car several times. Stalled on two occasions and hard to start. Realized there was no accelerator stream.

Rebuilt carburetor. Used the old automatic choke gasket until I realized it was interfering with choke coil. Then replaced gasket with new.

New ignition coil.

New points. Reset dwell.

Sandblasted plugs.


Between first time I ran it and now it has developed a loud tick.

Set valve clearances while warm and running.

Vacuum slightly over 16 psi with maybe .5 swing. Measured at about 340 RPM curb idle with about 10 RPM swing. RPM very stable.

Used stethoscope and loudest point seems to be on exhaust manifold between 1 and 2/3.

Vacuum and idle seem too stable for sticky valve but may be. About half of lifters rotate.


Could this be a lifter? The cam?


I have video/audio of vacuum, RPM and ticking if anyone could watch/listen.

Posted on: Yesterday 17:12
 Top  Print   
 


Re: Troubleshoot Loud Ticking 2498 288 Ultramatic
#2
Home away from home
Home away from home

53 Cavalier
See User information
Are your valve guides new?

Isn't a valve that bounces more an indication that the valve and seat are mating well? Shouldn't guides be reamed to spec? Maybe you have a tight guide that is causing a valve to stick?

Pistons were not removed, correct?

If the ticking sound is present at an idle, you could try removing plug wires one at a time to see if the sound goes away on a certain cylinder. If a valve is sticking open and being closed by the combustion cycle the sound should go away, or be less noticable when the plug wire is pulled.

Is the sound present both when the engine is cold and when it is at operating temp?

Share your video and let us have a listen. I'm curious! I had a ticking/tapping noise in my 327. It was rather illusive, and took a bit to track it down.

Posted on: Yesterday 17:58
 Top  Print   
 


Re: Troubleshoot Loud Ticking 2498 288 Ultramatic
#3
Home away from home
Home away from home

Pgh Ultramatic
See User information
- When is the noise most apparent? Low or high engine speeds? Heavy load, light load, deceleration?
- What frequency is the noise? Crankshaft speed or camshaft speed? Or is it irregular?

Could simply be an exhaust leak, the manifolds are known to warp and often need refaced..

And yes, share the video. Your accurate description of the problem is only as good as your own troubleshooting skills. In other words, if you think it's a valve noise, who are we to disagree except to hear it ourselves? But maybe someone will have a better guess.

Posted on: Yesterday 18:29
1955 400 | Registry | Project Blog
1955 Clipper Deluxe | Registry | Project Blog
1955 Clipper Super Panama | Registry
Email (Parts/service inquiries only, please. Post all questions on the forum.)
service@ultramatic.info
 Top  Print   
 


Re: Troubleshoot Loud Ticking 2498 288 Ultramatic
#4
Home away from home
Home away from home

kunzea
See User information
Are your valve guides new?

Response: No.



Isn't a valve that bounces more an indication that the valve and seat are mating well? Shouldn't guides be reamed to spec? Maybe you have a tight guide that is causing a valve to stick?

Response: Guides were reamed to spec.



Pistons were not removed, correct?

Response: Pistons were not removed.



If the ticking sound is present at an idle, you could try removing plug wires one at a time to see if the sound goes away on a certain cylinder. If a valve is sticking open and being closed by the combustion cycle the sound should go away, or be less noticable when the plug wire is pulled.

Response: Just tried removing plug wires one at a time with slight decrease in speed but no noticeable change in clicking.



Is the sound present both when the engine is cold and when it is at operating temp?

Response: Starts clicking within 20-30 seconds when started cold. Or at least becomes very noticeable after 20-30 seconds.

Posted on: Yesterday 18:36
 Top  Print   
 


Re: Troubleshoot Loud Ticking 2498 288 Ultramatic
#5
Home away from home
Home away from home

kunzea
See User information
- When is the noise most apparent? Low or high engine speeds? Heavy load, light load, deceleration?

Response: Most apparent at idle and during heavy acceleration.



- What frequency is the noise? Crankshaft speed or camshaft speed?

Response: On analog tachometer at about 550 RPM, the audio spectrum peaks are as follows:

1st peak is -30 dB at 112 hz
2nd peak is -29 dB at 1113.7 hz
3rd peak is -31 dB at 5672 hz.



Or is it irregular?

Response: It is regular.



Could simply be an exhaust leak,

Response: Frankly I believe there may be an exhaust leak. This was noticeable around the manifolds earlier in this process by using Seafoam and revving the engine. Subsequently, I torqued the manifolds to 30. If there are some more suitable tools I'd be happy to have them pointed out. I used a straight socket/extension on 1/8 and 3/6 nuts. I used a socket, universal joint and extension on 2/7. I used an offset open-ended crowfoot and extension on 4/5.



the manifolds are known to warp and often need refaced..

Response: The intake/exhaust manifolds were resurfaced as an assembly and installed and torqued IAW the "1951-1954 Service Manual" Engine_IX.pdf.. I did inadvertently run the engine pretty hot the first time I adjusted the valves. This was when the automatic choke wasn't operating freely.



And yes, share the video. Your accurate description of the problem is only as good as your own troubleshooting skills. In other words, if you think it's a valve noise, who are we to disagree except to hear it ourselves? But maybe someone will have a better guess.

Response: I can upload zip files to the forum. There is an Adobe web page that I hope I can use to zip the mp4.

Posted on: Yesterday 19:27
 Top  Print   
 


Re: Troubleshoot Loud Ticking 2498 288 Ultramatic
#6
Home away from home
Home away from home

Pgh Ultramatic
See User information
Interesting. Piston slap is common on old engines, but has the opposite symptom, as it is most apparent when the engine is cold, when the aluminum piston has the largest difference in size compared to the iron block.

Instead it seems like this sound occurs only when your oil has warmed up and hence is thinner. Offhand I would suspect that it is a piston wrist pin knock as that apparently sounds pretty similar to valve noise, and is most obvious at idle. The pin also doesn't move all that much compared to the crank, so the oil takes more time to heat up and thin out from viscosity.

The most apparent tell-tale is that it usually sounds like a double-knock.

I'm not aware of a way to diagnose this in particular, but it would stand to reason that grounding or removing the spark plug in the suspected cylinder should change the noise. Maybe #2 cylinder from what you said?

Edit:
Your spectrometer reading is:
- 1/4 crank speed (the normal firing noises of an engine that fires 8 cylinders over 2 crankshaft rotations)
- 2x crank speed (one noise per raise or lower of a given piston)
- 11x crank speed (maybe a double knock as I suspected?)

Posted on: Yesterday 19:30
1955 400 | Registry | Project Blog
1955 Clipper Deluxe | Registry | Project Blog
1955 Clipper Super Panama | Registry
Email (Parts/service inquiries only, please. Post all questions on the forum.)
service@ultramatic.info
 Top  Print   
 


Re: Troubleshoot Loud Ticking 2498 288 Ultramatic
#7
Home away from home
Home away from home

kunzea
See User information
There is a new development that I think just started today. There is a significant amount of water coming from the tailpipe. I mopped it up and restarted the engine. It expelled probably a 1/2 cup of water in maybe about a minute and is steaming.

After the engine got hot I re-torqued the head, anywhere from about 1/2 to 3/4 of a turn each. The head gasket is probably blown.

Posted on: Yesterday 21:03
 Top  Print   
 


Re: Troubleshoot Loud Ticking 2498 288 Ultramatic
#8
Home away from home
Home away from home

Pgh Ultramatic
See User information
Yeah, that could do it...

How many passes did you make originally and are you using an asbestos gasket? (Fiber between thin sheet metal if so, otherwise solid sheet metal.)

On a V8 which is half the head bolts, and a non-aesbstos gasket, I need to make 2 full passes at 60 before #1, on the 3rd pass, is at least at 55.

If using an asbestos gasket you have to retorque after a couple heat cycles then maybe again after some hundreds of miles. I forget the exact suggested routine.

Posted on: Yesterday 21:22
1955 400 | Registry | Project Blog
1955 Clipper Deluxe | Registry | Project Blog
1955 Clipper Super Panama | Registry
Email (Parts/service inquiries only, please. Post all questions on the forum.)
service@ultramatic.info
 Top  Print   
 


Re: Troubleshoot Loud Ticking 2498 288 Ultramatic
#9
Home away from home
Home away from home

TxGoat
See User information
It is normal for some water to be expelled from the exhaust after starting cold, especially in cool weather. Every gallon of gasoline burned releases about 3 gallons of water. Most of this will go out the exhaust as vapor, but when the engine and exhaust system are cool, some of it will condense and collect in the exhaust system, especially in the muffler and tail pipe. Repeated cold starting of the engine without driving the car can allow a substantial amount of water to collect. Many mufflers have small drain holes at one end to allow condensate to drain off. These are often plugged, which allows more water than normal to collect in the system. Starting and idling a cold engine will produce condensate in the exhaust system, and revving the engine after a short period of cold running may blow liquid water out the tailpipe. It's always best to run a car for at least ten miles whenever it is started, especially in colder weather. Not doing so will will allow water to collect in the exhaust system, and some will also get into the crankcase. If your car is in condition to drive, driving it on the road with some normal load on the engine for a few miles will allow heat to drive the moisture out of the exhaust system and the crankcase. In your case, I would re-torque the head and manifold assembly, following the correct procedure, and then drive the car for half an hour or more and watch for any evidence of problems. If you can't drive it, at least run it at a fast idle, about 1400 RPM, for 15 minutes or more.

Posted on: Today 9:58
 Top  Print   
 


Re: Troubleshoot Loud Ticking 2498 288 Ultramatic
#10
Home away from home
Home away from home

TxGoat
See User information
Visible exhaust steam is normal in cool weather, and if the exhaust system has collected water after a cold start, or series of cold starts, a lot of steam will be generated as the system heats up.

Posted on: Today 10:02
 Top  Print   
Like (1)
 




(1) 2 »





- The following Google Ad-Sense Advert helps fund the cost of providing this free resource -
- Logged in users will not see these. Please Join and Donate to help support the website -
Search
Recent Photos
Photo of the Day
Recent Registry
Upcoming Events
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved