Re: 1941 120 3 Speed with Overdrive Wiring?
|
||||
---|---|---|---|---|
Home away from home
|
The overdrive governor and solenoid are both electrically controlled and, if the car has Electromatic Clutch, then there may be some shift lever switches too. For just overdrive, none of the wires are needed for the transmission itself but, of course, they are if you want to use the overdrive. Packard did not use neutral lockouts on standard transmissions.
Posted on: 2023/11/26 15:40
|
|||
|
Re: 1941 120 3 Speed with Overdrive Wiring?
|
||||
---|---|---|---|---|
Just can't stay away
|
Quote:
Hmm.. I wonder if this is the electromatic clutch transmission. The dash is too far apart to see if there is a switch for it.
Posted on: 2023/11/26 17:05
|
|||
|
Re: 1941 120 3 Speed with Overdrive Wiring?
|
||||
---|---|---|---|---|
Home away from home
|
If so, there would be a valving device mounted to the rear side of the head on the drive side through which the throttle linkages go. If fully installed, there would also be a large diaphragm also on the driver’s side mounted low on the engine which is what actually actuates the clutch and a relay on the firewall that is large like a voltage regulator but with eight terminals.
Your photo, however, clearly shows an overdrive transmission as the solenoid and governor are there but not enough to see if it also has Electromatic. Overdrive and Electromatic were each available separately but when used together it was the closest Packard had in that era to an automatic!
Posted on: 2023/11/26 17:15
|
|||
|
Re: 1941 120 3 Speed with Overdrive Wiring?
|
||||
---|---|---|---|---|
Just can't stay away
|
Quote:
Ah OK..I don't think I have that then..
Posted on: 2023/11/26 17:29
|
|||
|
Re: 1941 120 3 Speed with Overdrive Wiring?
|
||||
---|---|---|---|---|
Forum Ambassador
|
As Don said, a couple of fairly large components on the side of the engine are needed to operate the clutch. Add to that, on your first photo, 7228, of the governor there is only one wire showing. If the car has an Electromatic clutch there would be a second wire on the governor so unless it is broken off I doubt the car has that option.. There would also be two switches on the transmission mounted on the side of the case opposite the shift levers. I did not see any wires going that direction.
Packard apparently did not provide actual photos of the engine showing the 41 EC components in manuals but there is an overall illustration of what you would see mounted on the engine and on the firewall in a 41 Service Letter.
Posted on: 2023/11/26 17:39
|
|||
Howard
|
||||
|
Re: 1941 120 3 Speed with Overdrive Wiring?
|
||||
---|---|---|---|---|
Home away from home
|
And the clutch pedal is black not red. I don’t think you’re missing out there as I see many of them left in « off »
Posted on: 2023/11/26 19:00
|
|||
|
Re: 1941 120 3 Speed with Overdrive Wiring?
|
||||
---|---|---|---|---|
Just can't stay away
|
Sooo...if I leave all the wires going to the transmission disconnected, what will happen?
Posted on: 2023/11/26 21:29
|
|||
|
Re: 1941 120 3 Speed with Overdrive Wiring?
|
||||
---|---|---|---|---|
Home away from home
|
If you’re not using the overdrive, nothing will happen but why do that? Unless you’re rewiring, maybe just leaving them alone is better
Posted on: 2023/11/27 2:42
|
|||
|
Re: 1941 120 3 Speed with Overdrive Wiring?
|
||||
---|---|---|---|---|
Home away from home
|
If you leave them disconnected for now the transmission will act as a normal three speed and the overdrive will not operate. You will need to move that one lever on the passenger side forward to prevent the trans from freewheeling. Once upon a time there was a knob under the dash for doing that but who knows if that is still there.
Looking at all the mung I can see why you say they put lipstick on a pig. Later on when other issues are under control you'll want the overdrive to work as it makes the car freeway capable.
Posted on: 2023/11/27 7:21
|
|||
|