Re: 1934 Packard 1104 Rear Axle
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
OK, confirmed. Part number is 207920 and the left and right are different.
Posted on: 2011/8/2 19:08
|
|||
Tom Laferriere - Smithfield, RI
1934 Packard 1104 Touring 1939 Packard 120 Coupe (in family since 1970) PH: 401.651.2295 Web: www.tomlaferriere.com |
||||
|
Re: 1934 Packard 1104 Rear Axle
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Tom you should have called Randolph's taxi. I would have done it for half that amount. :D
Posted on: 2011/8/2 19:10
|
|||
1938 1601 Club Coupe
|
||||
|
Re: 1934 Packard 1104 Rear Axle
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Phil, read again. Nothing was open in VT or any nearby city for that matter.
Posted on: 2011/8/2 19:13
|
|||
|
Re: 1934 Packard 1104 Rear Axle
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I deleted the rent-a-car thingie
Posted on: 2011/8/2 19:21
|
|||
1938 1601 Club Coupe
|
||||
|
Re: 1934 Packard 1104 Rear Axle
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Tom, I've pulled these axles quite a few times, most recently just last week to repack my rear wheel bearings. Its a very straight-forward and simple operation, seals readily available, but setting the axle shaft end play is critical and can take some special effort. Call me if you wish to discuss further, but you can read some details at:
http://www.packardclub.org/forum/viewtopic.php?f=15&t=266&start=10 Eight & Super Eight axles are different, as are left and right.
Posted on: 2011/8/2 22:28
|
|||
|
Re: 1934 Packard 1104 Rear Axle
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Dave,
As always, great information. The unique challenge I am going to have is to get the broken axle out. I probably will call you on this. Tom
Posted on: 2011/8/3 11:51
|
|||
|
Re: 1934 Packard 1104 Rear Axle
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Tom, I suppose they can break just about anywhere; about 5 or 6 inches from the housing flange is where mine broke back in 1999 and hopefully yours is similar and then the following should help. Regardless of how you want to approach it, you'll want to remove the inner seal to provide some working room. No need to remove the inner race. A strong magnet is one possibility though you need to wrap it in something to keep it from getting stuck against the housing bore as you insert it. But a length of fine, flexible wire, like picture hanging wire or a guitar wire, with a loop on the end should do the job Open the loop, insert into the housing bore, and with a small piece of dowel or something get the loop around the axle stub end. Then use the dowl to hold the loop in place while you pull the wire taught - and....viola! Something like the old Chinese finger toy is another possibility.
Posted on: 2011/8/3 12:00
|
|||
|
Re: 1934 Packard 1104 Rear Axle
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
left axle correct #207920 fits 33-34 super 8 only
Posted on: 2011/8/3 14:52
|
|||
|
Re: 1934 Packard 1104 Rear Axle
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Tom: If your axle broke near the spline you might find it instructive to read Neil Maken's article in the current (August) issue of Skinned Knuckles. It relates to his multiple rear axle failures on a 32 Nash, and his (and others) analysis of the problem. It would appear that inadequate axle shaft end-play might be the culprit, though that is not yet confirmed.
PS - spline end of a 1934 Eight axle shaft. Super 8 shaft dimensionally a bit different but same general style.
Posted on: 2011/8/4 10:37
|
|||
|