Re: Source For Valve Lash Measuring Tool For 359 Engine
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Pacific Northwest Packardshttp://pnwpackards.com/styled-2/index.html It is the first item on their project page.
Posted on: 2016/11/18 17:04
|
|||
Howard
|
||||
|
Re: Source For Valve Lash Measuring Tool For 359 Engine
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Thanks Howard!
Posted on: 2016/11/20 17:57
|
|||
|
Re: Source For Valve Lash Measuring Tool For 359 Engine
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
I have ordered the valve lash tool and await its arrival. In the meantime, the tick I am getting sounds to be only 1 valve/lifter and does not occur at start up. It is only once the engine has some heat in it that the tick starts. It was suggested that I change from 30 wt. motor oil to 40 wt. (I live in Florida) but the change in viscosity made no difference. Oil pressure is good. Thoughts?
Posted on: 2016/12/1 11:28
|
|||
|
Re: Source For Valve Lash Measuring Tool For 359 Engine
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Either you have a bad lifter or a valve sticking in its guide. Spraying some liquid wrench or similar at the bottom of the guide should free up the valve. This usually occurs on cars that have been sitting a long while and are started on old varnish smelling gas.
Valve stem to lifter clearance will change only if the valve face and/or valve seat are machined. It will not get too large or small by just running. The symptom you are experiencing is caused by the failure of an individual lifter. Either mechanical failure or dirt. The easiest fix is to replace the faulty lifter, new ones are available with improved design. It is necessary to remove the head and the offending valve. If you have not identified which lifter, remove the valve covers and idle the car. Either use a vacuum hose in your ear and put it next to each valve lifter or just touch the bottom of each valve spring. To confirm your diagnosis place a feeler gauge between the lifter and valve stem while running, large enough to fill the gap and it will get quiet. Remove the head, valve and offending lifter.
Posted on: 2016/12/1 11:53
|
|||
|
Re: Source For Valve Lash Measuring Tool For 359 Engine
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Possibly a speck of dirt stuck in the lifter check valve; might (small chance) work its way out over time. Also possible the lifter needs replacement. Any evidence of a sticking valve?
In any case chances are good that you're not doing any further harm by continuing to drive the car while you decide what if anything to do about it. PS - Fred, beat me to it, you're a fast man on the keyboard!
Posted on: 2016/12/1 11:54
|
|||
|
Re: Source For Valve Lash Measuring Tool For 359 Engine
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
If pressure is good and only one lifter is noisy then most likely a speck of dirt has gotten inside or else the lifter has a defective check valve. Have you been able to identify a specific area where the noisy lifter might be? Is there any damage to the small pigtail between the two oil ports on the drivers side of block? The oil fed into the upper hole above the oil sender is what supplies the lifter gallery. If the pigtail is damaged or partially crushed the flow could be restricted. The overall pressure could be good but the lifter pressure and flow could be a tad low. With only one noisy lifter it is doubtful that is the issue but if more than one then a possibility as another poster found a while back.
Posted on: 2016/12/1 12:00
|
|||
Howard
|
||||
|
Re: Source For Valve Lash Measuring Tool For 359 Engine
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Thanks guys. I will follow up on all suggestions and report back.
Posted on: 2016/12/1 14:00
|
|||
|
Re: Source For Valve Lash Measuring Tool For 359 Engine
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Have you received a fresh supply of 326 hydraulic lifters yet? Thanks Todd
Posted on: 2016/12/1 14:15
|
|||
|