Re: Distributor 53 Clipper 288
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Even with a electronic conversion (which are, I hear, dodgy with the 6-volt electrics) you will still need the bushings in good condition, because it operates from a modified cap and rotor.
I got mine rebuilt, new bushings, etc. by these guys: http://www.buchananautoelectric.com/ It's a standard Delco distributor (or Autolite) used on lots of Detroit iron, so the parts aren't a problem.
Posted on: 2022/7/2 13:37
|
|||
|
Re: Distributor 53 Clipper 288
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Rebushing your unit is straight forward and not complicated.
Posted on: 2022/7/2 13:43
|
|||
|
Re: Distributor 53 Clipper 288
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I need some assistance with my distributor. Can’t find a rebuilt one. I have emailed a couple of companies in CA about rebuilding mine and they haven’t responded. So, I guess I will undertake rebuilding mine. Where do I find the parts? I am striking out with my searches. It is a Delco remy unit. Thanks in advance
Posted on: 2022/7/7 17:47
|
|||
Even the most difficult situations can be learning situations.
1953 Packard Clipper 1957 Chevrolet BelAir 2004 Chevrolet Corvette |
||||
|
Re: Distributor 53 Clipper 288
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Hi Steve,
I wouldn't email Buchannan, I would call them. They are very old school that way. Jerome
Posted on: 2022/7/7 17:55
|
|||
|
Re: Distributor 53 Clipper 288
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Also, here's what's listed at the Kanter Website for 48-54 Packards for distributors:
Kanter 1948-54 Packard Parts GROUP 4.03001 ---- Distributor specify Autolite or Delco and tag number 4.03001 ---- Distributor, rebuilt, Exchange or add deposit of $95.00 $219.00 - See Note #1 4.03001 ---- Distributor with Petronix conversion, Exchange or add deposit of $115.00 (4.999) ---- Tune-up kit: contains points, condenser, cap, rotorand spark plugs Please advise if your distributor is Autolite or Delco. (23rd series advise if 10mm or 14mm spark plugs) $78.00 4.0305 ---- Points and condenser, replacement set $25.00 4.o305 ---- Points and condensor,1948-54 Autolite style new-old-stock points $39.00 4.0317 ---- Breaker plate (with points and condenser) most models available $140.00 4.0317 ---- Distributor bushing set of 2 $24.00 4.0317 ---- Cap and rotor $49.00 4.0317 ---- Vacuum advance Autolite, Exchange only $155.00 - See Note #1 4.0317 ---- Vacuum advance Delco, Exchange or add $50 deposit - See Note #1 $145.00
Posted on: 2022/7/7 17:58
|
|||
|
Re: Distributor 53 Clipper 288
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
If you can't find a local rebuild shop, many come up on search, they are out there. If it's that bad, it might need more extensive work though than just bushings, I'd be scouting a spare/core.
Brillman.com has some of the parts for distributors. Call if they don't show on line. There are other people with delco parts under other GM brands. You'd have to search. The obsolete Delco parts aren't available from them anymore. They used to let you look it up on line but that got sticky too. Actually any competent machine shop should be able to correct the bushings. This used to be more common, you could go to the local parts and get those small parts, but the computer and throw away/reman parts kinda did that in. Usually came with some advice on how to do it if you hadn't done before, or the corner garage. Those were the days.... Pull into one of the chain shops now and get laughed at when it's not on their computer. A distributor machine is another lost art here, but there's some out there. I keep passing them up as I don't want the expense and floor space tied up with something I'd use once or twice.
Posted on: 2022/7/7 20:14
|
|||
|
Re: Distributor 53 Clipper 288
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks guys. I will call Kanter
Posted on: 2022/7/7 20:20
|
|||
Even the most difficult situations can be learning situations.
1953 Packard Clipper 1957 Chevrolet BelAir 2004 Chevrolet Corvette |
||||
|
Re: Distributor 53 Clipper 288
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Here is the SUN distributor machine in action.
There is a crank to increase the rpm and check whether the dwell is stable (if not either worn bushing, worn breaker cam, worn mechanical advance, worn breaker point spring). The position for number one cylinder is set using a calibrated plate on the face of the machine and when the machine is running the lights for the other cylinder should be in the correct positions and steady. On the top of the machine is a roll index that has the specs for various distributors which, if present, should match the manual. As the rpm is increased the position of the lights should move with the mechanical advance. Performance tuners used these machines to set the advance curves to match the cam and compression ratios. I knew one engineer who was fired and used this machine to set up drag race motors. He got rich. Another feature is to dial in and check the vacuum advancer. Condenser condition is another test. A performance tuner can use this machine to match the advance curve to the compression ratios of a particular car. I've seen that done to increase the horsepower on a stock motor by 40 hp on the dyno. I'm sure a lot of Packards would benefit from something like that and run cooler as well. Attach file: ![]() ![]()
Posted on: 2022/7/8 6:35
|
|||
|
Re: Distributor 53 Clipper 288
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Not sure about replacing bushings in a Delco... I do know replacing the bushings in an autolite is pretty straightforward. Alterntively, I have an autolite unit sitting on the shelf here, new bushings installed that you are welcome to for a donation to the site. The experts can certainly comment on which is better or otherwise.
DAF
Posted on: 2022/7/8 7:18
|
|||
|