Re: broken gear shift lever 1931 Packard 840
|
||||
---|---|---|---|---|
Not too shy to talk
|
here is the photo
Attach file: (46.72 KB)
Posted on: 2014/5/27 6:27
|
|||
|
Re: broken gear shift lever 1931 Packard 840
|
||||
---|---|---|---|---|
Home away from home
|
I think I might have what you need, if you want to go the "replacement" route. Cost would be around $150, plus shipping.
Posted on: 2014/5/27 9:11
|
|||
West Peterson
1940 Packard 1808 w/Factory Air 1947 Chrysler Town and Country sedan 1970 Camaro RS packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=4307&forum=10 aaca.org/ |
||||
|
Re: broken gear shift lever 1931 Packard 840
|
||||
---|---|---|---|---|
Forum Ambassador
|
The cane and it's associated mechanism call all be serviced from above. Just remove the carpet and whatever is necessary to get to the case cover.
Posted on: 2014/5/27 9:31
|
|||
|
Re: broken gear shift lever 1931 Packard 840
|
||||
---|---|---|---|---|
Not too shy to talk
|
regarding the replacement part, do you have any photos or a website i can access?
thanks Robert
Posted on: 2014/5/27 11:51
|
|||
|
Re: broken gear shift lever 1931 Packard 840
|
||||
---|---|---|---|---|
Home away from home
|
If down the road, you want to have this one fixed, take all related parts to a reputable weld shop. From what I see in your picture, the penetration of the weld was not good on the piece that the shifter shaft went in to. Some machining to that part to weld it correctly may be in order to get it done properly.
Posted on: 2014/5/27 13:12
|
|||
|
Re: broken gear shift lever 1931 Packard 840
|
||||
---|---|---|---|---|
Home away from home
|
I found a replacement shifter for you. I forgot to take it out of my wife's truck, so I can't take a photo of it now, but will do so asap (this afternoon). It's in very nice condition. Not rusty. Ready for paint ... or chrome. This one is painted.
Posted on: 2014/5/28 8:41
|
|||
West Peterson
1940 Packard 1808 w/Factory Air 1947 Chrysler Town and Country sedan 1970 Camaro RS packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=4307&forum=10 aaca.org/ |
||||
|
Re: broken gear shift lever 1931 Packard 840
|
||||
---|---|---|---|---|
Not too shy to talk
|
West,
I will take it. 150 plus shipping. Let me know the total and I will send to you. Just let me know your mailing address. thanks Robert
Posted on: 2014/5/28 10:57
|
|||
|
Re: broken gear shift lever 1931 Packard 840
|
||||
---|---|---|---|---|
Home away from home
|
Hmmm. I just looked at the shifter I have saved for the Speedster (see attached). It is slightly different than the one I pulled for you in that it has the swivel ball. I'll have to go back and see if I can find a good shifter with a ball for you.
Unless... the balls are removable????? Are they pressed on??? Take yours apart a little further and see if there's a ball on it, and if it's removable. You can e-mail me at StelvioGT@yahoo.com with your mailing information, and I'll send you my information as well.
Posted on: 2014/5/28 11:56
|
|||
West Peterson
1940 Packard 1808 w/Factory Air 1947 Chrysler Town and Country sedan 1970 Camaro RS packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=4307&forum=10 aaca.org/ |
||||
|
Re: broken gear shift lever 1931 Packard 840
|
||||
---|---|---|---|---|
Home away from home
|
I just realized... the "divot" you see in the ball is for a pin. Remove the pin, and the ball should slide off.
Posted on: 2014/5/28 12:52
|
|||
West Peterson
1940 Packard 1808 w/Factory Air 1947 Chrysler Town and Country sedan 1970 Camaro RS packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=4307&forum=10 aaca.org/ |
||||
|