Re: John's 1935 1201 Coupe for Two or Four Passengers, RHD in Tasmania
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Thanks Andy. PM sent. Cheers, John
Posted on: 2016/7/18 23:32
|
|||
|
Re: John's 1935 1201 Coupe for Two or Four Passengers, RHD in Tasmania
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
John,
Before you go any further, a block of wood between the jack and the sump(pan) would be a good idea to cover the "first, do no harm" premise. Regarding the stuck sump, use as thin a blade as you can to start the process. A putty knife or paint scraper should be suitable. Try different points around the edge of the sump and wiggle/wedge it in as far a you can. Judicious use of a persuader, aka hammer, ![]()
Posted on: 2016/7/20 23:14
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: John's 1935 1201 Coupe for Two or Four Passengers, RHD in Tasmania
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I used a brake adjustment tool that was ground a little more on the end and pried ever so softly then ran a razor blade down the crack to separate the gasket.
Good luck
Posted on: 2016/7/21 15:37
|
|||
[url=http://packardinf
|
||||
|
Re: John's 1935 1201 Coupe for Two or Four Passengers, RHD in Tasmania
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Thanks Mal and Desk Driver.
With your advice in mind, I'll spend some time on it on Sunday. I think I'll investigate removal of the right-side floor panel first, which looks a little trickier because it hugs the RHD steering assembly and exhaust. I'll have to do this carefully because there are loose and fragile remnants of insulation lagging hanging from the exhaust which I assume are asbestos. I will have to take some time to carefully shroud the asbestos before I proceed. Then I'll take the time to patiently clean up all around the sump (oil pan) before finally attempting the careful separation you both endorse. Thanks and cheers, John PS: A big shout out for AJS who kindly sent me a set of pictures of his identical engine from his Phaeton, to use as a reference. Thanks Andy! Really appreciate the generous spirit within this forum.
Posted on: 2016/7/21 18:10
|
|||
|
Re: John's 1935 1201 Coupe for Two or Four Passengers, RHD in Tasmania
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
When you're carefully prying the oil pan off (good advice given so far) also be mindful that you don't gouge the aluminum sump, as then there will be issues with sealing the gasket on upon reassembly. Slow and easy will give you the desired result, avoid the temptation to just pry on something trying to hasten the process. As I always remind myself, "they don't make these anymore ".
Posted on: 2016/7/21 22:10
|
|||
1952 Model 200 Deluxe Touring Sedan
HA's 52 Grey Ghost "The problem with quotes on the internet is you never know if they're true" - Abraham Lincoln |
||||
|
Re: John's 1935 1201 Coupe for Two or Four Passengers, RHD in Tasmania
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
John,
If all else fails and you cannot get it apart you may try heating the flange with a heat gun. Adhesives generally let go at around 200 deg C. I don't know if you can get it that hot but it could be worth a try. Good luck
Posted on: 2016/7/22 2:57
|
|||
|
Re: John's 1935 1201 Coupe for Two or Four Passengers, RHD in Tasmania
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Hi John,
The door hinge cover screws are on their way. All the best with the sump. Phil
Posted on: 2016/7/27 21:39
|
|||
|
Re: John's 1935 1201 Coupe for Two or Four Passengers, RHD in Tasmania
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Thank you so much HA52, David M and Phil.
I worked around the car all day on Sunday but was ultimately unable to lay a finger on it. I spent the first half of the day clearing more of the old junk from around it so I can access it better. It culminated in getting bogged with a trailer load of old junk ready to cart away. I've only got highway tyres on the Land Rover and they all just spun in the mud. I'm not convinced the diff-lock was engaging correctly either. Anyway, by the time I'd sorted that out, all Packarding time had evaporated. Frustrating, but I'll have to be patient. Heaps more heavy rain forecast for the next 2 weeks so the area around the shed will remain as boggy as a Byron Bay Blues Festival for a while. I hope to spend this coming Sunday on the actual car; not just the peripheral shed problems. I'll let you know how it goes prying off the sump. Phil, that is exciting news! Thank you so much. Please just let me know what I owe you for those. I hope we can get you back down for when we are ready to try firing up the car; but the more I do, the further in the future that seems. All the best for now, John
Posted on: 2016/7/28 4:28
|
|||
|
Re: John's 1935 1201 Coupe for Two or Four Passengers, RHD in Tasmania
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Sometimes some gentle tapping around the bottom edge of the oil pan with a rubber hammer will make the pan come loose...Ernie
Posted on: 2016/7/31 12:52
|
|||
Caretaker of the 1949-288 Deluxe Touring Sedan
'Miss Prudence' and the 1931 Model A Ford Tudor 'Miss Princess' ![]() |
||||
|