Re: Universal Power Brake Conversion
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
There have been several who have mounted thru the air vent as you are considering. Don't recall any using a universal kit though. Here is a thread with one of the first as well as an excellent conversion with the booster mounted higher up toward the top of firewall. There is another vent conversion done by a friend of Craig's who did one using IIRC, a Chevy pedal setup. Can't think of the title of that thread but perhaps Craig will see this and remember the post.https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=2874&viewmode=flat&order=ASC&type=&mode=0&start=0
Posted on: 2017/2/14 22:27
|
|||
Howard
|
||||
|
Re: Universal Power Brake Conversion
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks Howard. I saw that thread, and possibly one other, but there was a lot of discussion regarding the pedal ratio and some that required using different pedal mounts or modifying the stock pedal. I was wondering about the ones that are inclusive of the pedal, linkage, etc.
Hopefully, someone else has decided to take this route and has some info, because it will be awhile before mine is street legal. ;^)
Posted on: 2017/2/14 22:33
|
|||
|
Re: Universal Power Brake Conversion
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Using the 94 Ford explorer PB unit AND PEDAL ASSEMBLY (need TWO pedal assemblies) is about as close to a "bolt in" conversion as is available. Yes, some minor mods to the Ford pedal needs to be made but not that would require the skills of a master fabricating professional with 50 years experience.
Maybe need to go back and study the various threads regarding this conversion. The pedal ratio u seem worried about is ELEMINATED when using the ford power unit AND Ford pedal assembly. If the Ford ratio was correct for the Ford app then it is correct even if mounted on a sewing machine a Boeing 707 or a highway tractor.
Posted on: 2017/2/15 16:57
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: Universal Power Brake Conversion
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Here is a well documented thread on converting a '55 Oldsmobubble with the DTV.
http://classicoldsmobile.com/forums/vintage-oldsmobiles/53873-under-floor-power-brakes-1955-olds.html
Posted on: 2017/2/15 19:04
|
|||
|
Re: Universal Power Brake Conversion
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
No info seems to be forthcoming on anyone using a universal kit on a Packard so it looks like no one has tried any of the firewall kits.
Just thinking out loud, but since some of the limiting factors is length and having to give up a function such as the vent or other firewall real estate and in addition to that fabrication, also possibly need to relocate electrical components for clearance, I am wondering about one of the under floor kits. IIRC, a few years ago there was a poster who thought they would not fit but has anyone actually measured the space to the rear of the accelerator over near the frame X. Packard placed their manual cylinder in that area in 55-6 so maybe a dual 7" booster would fit. Even if it hung down an inch below the frame it would probably not be a show stopper. Add a protection plate if needed and with a remote reservoir, it would be a neat and almost invisible mod. If the underfloor setup would fit I wonder if it would be possible to go a step farther and modify the arm by shortening a bit. Add a bearing arrangement on the end of the floor arm which could be worked by rolling against a plate arrangement on the back of the suspended pedal. Because of the two different geometries the bearing would have to be able to roll as the suspended pedal moved and also be captured to keep them together but I think it might be doable. If not a bearing possibly some kind of double clevis link. Add a bellows over the exposed floor arm and inside, the mod would look virtually identical to stock and still have the proper ratio..
Posted on: 2017/2/15 19:57
|
|||
Howard
|
||||
|
Re: Universal Power Brake Conversion
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Quote:
Too bad the photos are not visible to non members. It might be an interesting read.
Posted on: 2017/2/15 20:01
|
|||
Howard
|
||||
|
Re: Universal Power Brake Conversion
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I have the pics here are few has lots of detail for installation in Olds
Posted on: 2017/2/16 12:03
|
|||
|
Re: Universal Power Brake Conversion
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Thanks for obtaining the photos. The pedal location is interesting. Was it originally that low in the Olds? The pedal arrangement and location looks a lot like the mods Craig worked out for his conversion.
I was trying to keep the pedal location totally stock looking but don't like the complexity of my approach and where the booster wound up. Still haven't got back to that project as the 47 took over. Am kind of intrigued with the floor mount possibilities though. There looks to be some power floor mount kits for 55-7 Chevys and doubt if those had any deeper frames than a Packard
Posted on: 2017/2/16 12:23
|
|||
Howard
|
||||
|
Re: Universal Power Brake Conversion
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
The pedal location is interesting. Was it originally that low in the Olds?
No.
Posted on: 2017/2/16 12:42
|
|||
|