Re: 51 Clipper Backing plate gasket
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I don't think it is to bad of a job. I know I've read threads here on various member that have done theirs. Probably some one will chime in here with links and advice.
Posted on: 2021/3/24 18:56
|
|||
|
Re: 51 Clipper Backing plate gasket
|
||||
---|---|---|---|---|
Webmaster
![]() ![]() ![]() |
You can see my project blog to see details of this. The backing plate seals directs oil/grease that leaks out of the axle to direct it out of the weap hole down the outside of backing plate. But if it's leaking, then its the axle seals that need probably need to get replaced. 80% of the battle is pulling the drums..after that pulling the axles is not a big deal as they don't require you to open the diff up. They just pull out after the backing plates are removed.
Posted on: 2021/3/24 19:35
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Re: 51 Clipper Backing plate gasket
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Steve, keep track of the shims. Do not mix them up. It is important to return them to their respective side to maintain axle shaft end play.
Posted on: 2021/3/25 10:21
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: 51 Clipper Backing plate gasket
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
You can make the gaskets as they are nothing special and fairly easy to cut but Max Merritt and probably Kanter might have them as a gasket only set. I know Max has complete axle kits with new seals, gaskets and bearings but not sure about gaskets only. You might be able to match the seals at Napa but be careful of the depth. Most of the seals cross to modern with identical ID and OD specs to the originals but I have found the depth sometimes varies. At times the modern depth is too wide and causes clearance issues with the retainer pieces.
If you are going far enough to remove the axle to replace that inner seal you can perform routine maintenance by doing a lube and check of the bearings at the same time. Suggest you read thru the rear axle section on removing the axle and packing the bearings. Also take heed of the caution not to beat on the ends of the axle when using certain types of drum pullers. Sometimes the axle and seal will come out without out much effort but if you need a puller tool such as Packard used, a workable version can be fabricated with a common body shop slide hammer. For the axle use a coupling nut sized to fit the threads on the axle and a hex head bolt that will screw into the other end of the nut. Drill and tap the head of the bolt to fit the attachment end of the slide hammer. For the tool used to grab the seal it is a bit more work as you need to bend the ends of some flat stock to form something that can reach behind the seal to pull it out. You can either make the other end so it can attach to the slide hammer or wide to use a hammer like the original tool. It also might need something in the middle to keep the ends spread apart similar to the original tool. The axle end play checking tool has been mentioned in other posts and a search should find those posts and photos of the home made version. It is important to keep the axle shaft from scraping over the new seal when sliding it back into the housing. That can be assisted by making a lever arrangement using the same coupling nut on the axle and a length of all thread instead of the bolt. I found the connection to the slide hammer was too weak to use for the lever so allthread was used instead. Thread the nut and allthread back on the shaft and use the other end of the allthread as a control to lift or hold the shaft up so it does not scrape the seal.
Posted on: 2021/3/25 11:06
|
|||
Howard
|
||||
|
Re: 51 Clipper Backing plate gasket
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
thanks for this advise. I noticed that one side had one shim and the other several. Appreciate the heads up!
Posted on: 2021/4/20 10:30
|
|||
Even the most difficult situations can be learning situations.
1953 Packard Clipper 1957 Chevrolet BelAir 2004 Chevrolet Corvette |
||||
|
Re: 51 Clipper Backing plate gasket
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
The number of shims on a side does not matter. You only need to adjust one of the axles for the end play.
Posted on: 2021/4/20 10:57
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|