Re: 2262 Rear Tire Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
- Take off the fender skirt.
- Deflate the tire. My guess is someone put ill-fitting radials on it that are a fair amount too wide. What is the tire size as indicated on the sidewall?
Posted on: Yesterday 21:21
|
|||
1955 400 | Registry | Project Blog
1955 Clipper Deluxe | Registry | Project Blog 1955 Clipper Super Panama | Registry |
||||
|
Re: 2262 Rear Tire Removal
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
I did take off the skirt, before I did anything else. It has the correct size tires, based upon Factory spec, which is 7.60 x 15, made by Coker Tire.
Posted on: Yesterday 21:25
|
|||
Todd W. White
Sapulpa, Okla. 1949 2262 DeLuxe Eight Touring Sedan |
||||
|
Re: 2262 Rear Tire Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Are your stands under the frame or axle? On my 53 I need to jack from.the frame so the axle is low enough to get the tires off.
Posted on: Yesterday 21:32
|
|||
|
Re: 2262 Rear Tire Removal
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
If you did jack from the frame do you see anything pulled tight such as a brake hose or emergency brake cable that could be preventing a drop? Since the issue is on the left side how about the 5th shock/horizontal stabilizer. Could that be a repro or repaired unit that possibly doesn't have enough travel.
Posted on: Yesterday 21:35
|
|||
Howard
|
||||
|
Re: 2262 Rear Tire Removal
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Well, traditionally, I've always put them under the axle, but I've never had a car with fender skirts on it, so I didn't even think about putting the stands under the frame itself. I will try that in the morning.
Thank you!
Posted on: Yesterday 21:40
|
|||
Todd W. White
Sapulpa, Okla. 1949 2262 DeLuxe Eight Touring Sedan |
||||
|
Re: 2262 Rear Tire Removal
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Hi and thanks for your reply.
Well, I guess I didn't the state it very well. I'm able to get the lug bolts out, and release the tire that's attached to it from the hub. My problem is, even after having taken off the skirt, there is not enough clearance to get the tire/wheel out of the wheel well. It is hanging up somewhere (and I ran out of daylight so I'm not sure exactly where), but I think it's hanging up because there's not enough clearance between the inside edge of the Fender and the end of the axle. I am guessing that what others have suggested, namely, that instead of jacking up the back end and resting the axles on jack stands, that I should put the jack stands under the frame and rest the vehicle on the jack stands using the frame, thereby allowing the axle to lower enough to get the wheel/tire out of the wheel well.
Posted on: Yesterday 23:29
|
|||
Todd W. White
Sapulpa, Okla. 1949 2262 DeLuxe Eight Touring Sedan |
||||
|
Re: 2262 Rear Tire Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Quote:
Yes, definitely jack from the frame and let the axle hang. If needed you can deflate the tires. Probably not necessary though. -Kevin
Posted on: Today 0:17
|
|||
|
Re: 2262 Rear Tire Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Quote:
Your question was clear enough. These cars came with a bumper jack, which if used would create lots of clearance by the time the wheel was off the ground. But they are a bit sketchy and I wouldn't use it for more than show. Enjoy your car!
Posted on: Today 2:05
|
|||
|
Re: 2262 Rear Tire Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Quote:
Your question was clear enough. These cars came with a bumper jack, which if used would create lots of clearance by the time the wheel was off the ground. But they are a bit sketchy and I wouldn't use it for more than show. Enjoy your car!
Posted on: Today 2:05
|
|||
|