Packard Forum Index » Project Blogs

Topic: Rusty McRustface - Misadventures with a 1953 Clipper Deluxe

Bottom

Previous Topic

Next Topic Register To Post

« 1 2 3 4 (5)

Ross

Re: Rusty McRustface - Misadventures with a 1953 Clipper Deluxe

#41

Home away from home

Here we go--it is just some tubing welded together and fitted with little feet to keep it from shifting out of the lift slides. I just loop chain around it and into my lifting bracket which picks up any two studs, non adjacent, in the center row of studs. By looping the chain over the bar, I can tap the chain left and right with a hammer to center an engine up on installation.

I always remove the hood for space and for the light. Just shove a bunch of towels under the back corners and have someone hold up the front while you take the bolts out. It really is just 5 minutes.

Attach file:

IMG_1036.JPG (1,820.33 KB)

IMG_1037.JPG (1,709.90 KB)

Posted on: Yesterday 13:22

humanpotatohybrid

Re: Rusty McRustface - Misadventures with a 1953 Clipper Deluxe

#42

Home away from home

Quote:

56Clippers wrote:
With a set of pulleys, the hood is a one person job.
Using that lift, pulling the V8 and transmission was a tight fit, but I left the bumper and grill on.
The transmission mount was too restrictive to leave in place, I removed it to gain maneuvering room.

Where did you get the fender mat?

Posted on: Yesterday 13:30

Ken_P

Re: Rusty McRustface - Misadventures with a 1953 Clipper Deluxe

#43

Home away from home

I have the same one, one of the clubs was selling them some years back. They were advertised in the back of the monthly Packard Club publication.

Quote:

humanpotatohybrid wrote:

Where did you get the fender mat?

Posted on: Yesterday 14:38

1937 120 1092 - Original survivor for driving and continued preservation. Project blog / Registry

1937 115 1082 - Total basket case, partial restoration, sold Hershey 2015 Project blog / Registry

kevinpackard

Re: Rusty McRustface - Misadventures with a 1953 Clipper Deluxe

#44

Home away from home

Quote:

Ross wrote:
Here we go--it is just some tubing welded together and fitted with little feet to keep it from shifting out of the lift slides. I just loop chain around it and into my lifting bracket which picks up any two studs, non adjacent, in the center row of studs. By looping the chain over the bar, I can tap the chain left and right with a hammer to center an engine up on installation.

I always remove the hood for space and for the light. Just shove a bunch of towels under the back corners and have someone hold up the front while you take the bolts out. It really is just 5 minutes.

Thanks Ross, that's exactly what I was looking for. I have a bit of a lip on the lift slides that I can use to make some feet, maybe 1/2". I think yours is deeper. But assuming the bar doesn't flex too much it should work. Now I'm on the hunt for some scrap metal to use.

Click to see original Image in a new window

-Kevin

Posted on: Yesterday 16:04

56Clippers

Re: Rusty McRustface - Misadventures with a 1953 Clipper Deluxe

#45

Home away from home

Quote:

humanpotatohybrid wrote:

Where did you get the fender mat?

Mine didn't come from the club. I don't remember where I got it.
The small text along the bottom is "The Original FENDER GRIPPER" and "Made in the U.S.A".
I found them listed at ALL-ROUNDTOOLKING

Posted on: Today 12:08