Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Nice neat work Howard. When the carpet is in place, no one will notice. Good pictures - self explanatory.
Posted on: 2012/1/14 19:52
|
|||
|
Re: Progress report
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Wonderful projects in design and implementation. I know that the original Packard engineers would've been proud to greet you as an equal. It's amazing how these autos still inspire creation. Thank you Howard for your designs, we all owe you for your help.
Posted on: 2012/1/14 22:24
|
|||
Bob
IF EVERYTHING IS COMING YOUR WAY ... - - - - - - - - - - - - - - - - - - - - - - - - YOU'RE IN THE WRONG LANE! '56 Executive Touring Sedan |
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Superb electrical work thru out. One exception: I am surprised that the Headlite switch is using the solderless terminals with teflon insulators still in place. I assume that was was just a pic during a Q&D mock-up???
Does the GM headlite switch fit the dash and Packard bezel with no modicications to the switch????
Posted on: 2012/1/14 23:37
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Maybe put a 1/2" to 1" radius on the toe plate corners to keep the the corners from wearing thru the carpet in short order.
Posted on: 2012/1/14 23:43
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Quote:
Keith and everyone who commented, thanks. Hard to see in that picture but no crimp marks on the terminals so they are soldered. Here is another picture showing how the insulators are removed and wires are soldered directly to terminals. If done carefully without runs of solder on the outside of terminals, the covers slide back on. Maybe overkill but more comfortable knowing they have a good solid connection and keeping the covers gives a bit of extra to hold during installation. Other than bending a tab, the switch itself requires no changes but is not just drop in. Does require a slight bit of work to the mounting nut and shaft for the Packard bezel and knob-- but nothing outrageous needing more than a saw and file. I also went a slight bit extra in wiring because I wanted no changes to the stock Packard loom. Instructions and parts are in the pdf file posted in the original thread.https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?post_id=83907#forumpost83907 If you want them & can't download pdfs, I can convert to something else or email. Thanks for the radius suggestion on the brake plate. Once it is proven satisfactory in function, was considering another try. Since it can mount as a unit after all & doesn't seem to need to be made in pieces for assembly in car, another version may be possible. Would still like to get the shaft nearer to original location and make sure it works with regular shift linkage cars. Problem is unless something turns out to be a failure on this one, I probably won't be taking my car apart again to use as a test mule. Any little leverage changes needed I can make with provisions already there but doing complete assys with the seat and AC blower in place is another story. Was a project and contortion exercise just adding a torsion spring to the pedal as an afterthought. With no cars to play with closer than 50 miles, it may not happen.
Posted on: 2012/1/15 11:00
|
|||
Howard
|
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Nice work, Howard. We all benefit from seeing carefully thought-out and executed projects; especially those where changes can be removed with no evidence of their existence.
(o[]o)
Posted on: 2012/1/15 12:11
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I'll make Ross' transmission mods next week if the mood strikes and the weather co-operates...
And what are these modifications and where does the info lurk?
Posted on: 2012/1/16 0:15
|
|||
When two men ride the same horse, one has to be in the back...
|
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Three of them. A shortened spring, extra shim and a plate partially blocking a reverse piston port. Detailed in these threads.
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?post_id=50850#forumpost50850 https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?post_id=58127#forumpost58127
Posted on: 2012/1/16 0:23
|
|||
Howard
|
||||
|
Re: Progress report
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Quick point to mention, Howard, if you place your shim in the bottom of the shift piston as I do, it must have a good sized hole through it as there is fluid flow through the piston. You will notice the hole in the bottom of the piston.
To make my shim pack, I usually flatten a 1/4" lockwasher, and grind its OD a hair on the bench grinder so it fits inside the piston nicely. This will be sure to leave the hole in the poston uncovered. Then I add a 3/16 flatwasher on top of that to get the .120/.130 package I am looking for. Look forward to hear your feedback.
Posted on: 2012/1/16 5:33
|
|||
|