Re: 56 V8 valve lifters
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Yes, been covered and no, the Packard V8 lifters are not the same as the later Mopar 318" V8. Those Mopars use a 5/16" pushrod seat. The Packard pushrods are 1/4" balls.
The Mopar lifters will go in the hole and the Packard engine will run, but the pushrod and seat will wear faster. jack vines
Posted on: 2015/7/25 14:51
|
|||
|
Re: 56 V8 valve lifters
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
being an Egge retailer, I get them cheaper than that. Out of curiosity, what part number are you referencing for Autozone? I believe the 318 uses a larger seat.
Posted on: 2015/7/25 15:05
|
|||
[url=https://packardinfo.com/xoops/html/modules/
|
||||
|
Re: 56 V8 valve lifters
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Jack, when using the Mopar 879 lifters, have you attempted to change the ball insert on the end of the pushrod for a correct fit?
Posted on: 2015/7/25 15:26
|
|||
|
Re: 56 V8 valve lifters
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Go look at the Packard Parts X-ref of this web site.
Not clear to me why the 5/16 seat (ASSUMUNG HYDRAULIC lifters) would cause any faster wear of the pushrod. Maybe solid lifters yes. But not hydraulic. In 1997 and 30K miles ago i installed the (from my book) "mid-60's 318 MoPar lifters" No problems thus far after 30K miles. SEE THE X-ref for further detailss in comment section.
Posted on: 2015/7/25 21:56
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: 56 V8 valve lifters
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
From the X-ref comments:
" Packard V8 hydraulic valve lifters: Melling JB 879 or SealedPower HT 879. DO NOT USE THE 2011 LIFTER !!!!!!!! I have the JB879 installed in my 56 Executive. When i pulled it apart there were 2 replacement types in there that i have reasons to believe came from one of the major suppliers. The 879 lifters are identicle to the 2 replacements i found in the engine EXCEPT for the shape of the pushrod seat. The 879 has apushrod seat identicle to the factory lifters that was in the car."
Posted on: 2015/7/25 22:00
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: 56 V8 valve lifters
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Not clear to me why the 5/16 seat (ASSUMUNG HYDRAULIC lifters) would cause any faster wear of the pushrod.
Because the ball end of the pushrod will be able to "walk" within the larger socket and all the stress on the ball and socket base will be concentrated in a smaller area. How significant this might be in terms of premature wear I don't know.
Posted on: 2015/7/25 22:48
|
|||
|
Re: 56 V8 valve lifters
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I don't know. I've never tried an accurate measure of any oem lifter seat radius nor any oem push rod ball end radius. But i would highly suspect at least a .005" differencce in the radius between the ball end and the seat. Maybe more like .015".
OR, What is the trade off???? A repop no-name UNbranded lifter with a "1/4 inch" seat or a BRAND NAME lifter with a 5/16" seat. I don't know. THe HYDRAULIC lifter should keep some pressure on the pushrod and thus pussh rod centered in the seat in the lifter anyway so why suspect much walking. On top of that, everyone seems to think thay have to unconditionaly deck blocks and mill heaads thus changing the push rod angle anyway. I suppose the real question is: Which trade offs are the mosst benficial???? Unless there are plenty of NOS or NORS lifters still available.
Posted on: 2015/7/26 10:57
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: 56 V8 valve lifters
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Quote:
Go look at the Packard Parts X-ref of this web site. The OP referenced "the same lifter that Chrysler used later in their 318 engine." Well, sorta, but one has to define how much later and which 318". The early Mopar lifters from the rare late '50s wide-block 318" and other '50s-early '60s are the same as the Packard. However, they're not available in most FLAPS. The difficulty comes when someone goes into a parts house and confidently states "gimme some 318" lifters" and gets the #2011s, which are the only commonly available 318" lifters. The correct #879 lifter is still readily available from those who know the difference. Why go looking for trouble? jack vines
Posted on: 2015/7/26 20:21
|
|||
|
Re: 56 V8 valve lifters
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Jack, thanks for that clarification!
Posted on: 2015/7/26 22:17
|
|||
|