Re: Update on 356 CI Block
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
The "wax method" may go back to as early as the days of the Industrial Revolution and it sometimes produces very rewarding results. Always worth a try.
Posted on: 2020/12/11 14:25
|
|||
|
Re: Update on 356 CI Block
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Maybe a hand impact? I have an impact driver that has different bits that come with it. You hold the impact and strike with a hammer and it rotates maybe an 1/8 of a turn.
Posted on: 2020/12/11 16:57
|
|||
|
Re: Update on 356 CI Block
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I had thought of that too but it would need to be used carefully to avoid cracking the casting, They work very well, though.
Posted on: 2020/12/11 17:05
|
|||
|
Re: Update on 356 CI Block
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks again, for all the suggestions and input......
Using the various methods suggested, I was able to remove all of the pipe plugs feeding the cam bearings. First of all, I soaked the plugs with PB Blaster for about a week. Secondly, I used a Mapp torch on each one. The final approach was to use an impact screwdriver. The plugs were soft and fortunately broke loose before the slots were completely deformed. BTW, I tried the wax suggestion and it performed as well as the ones with the PB Blaster. Unfortunately, The two main plugs in the ends of the oil gallery will have to be drilled out. They have a 3/8" female square that is very shallow. I'm not sure how the factory planned on removing these, but they are only about 1/8" deep. I'm not aware of any tool that will remove these. Thanks again for all the help
Posted on: 2020/12/14 19:54
|
|||
Steve P
Forest, Va 1929 645 Dual Cowl Phaeton 1937 120C Conv Coupe 1940 1389 Conv Coupe 1940 1377 Super 8 160 Conv Sedan |
||||
|
Re: Update on 356 CI Block
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
If the square recess is a standard 3/8 size would a length of square stock from the hardware store work if you cut off a piece and used it with a 4 point or 8 point socket? Not sure if a 12 point socket would work on square stock but maybe. If no bar stock is available at the local hardware store McMaster has a good selection of short inexpensive lengths in alloy steel as well as 4 and 8 point sockets.
Posted on: 2020/12/14 20:44
|
|||
Howard
|
||||
|
Re: Update on 356 CI Block
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Great to hear you got those out.
If I remember correctly the business end of the standard impact screwdriver is 3/8" square, but it might have the end rounded a bit so maybe it wouldn't sit deep enough in the recess. However, one of these might, again attached to the 3/8" impact screwdriver. Might be able to find one of these or similar at your local hardware store or order online. https://www.homedepot.com/p/SUNEX-TOOLS-Pipe-Plug-Socket-Set-SUN2841/300683345?source=shoppingads&locale=en-US&mtc=Shopping-B-F_D25T-G-D25T-25_1_HAND_TOOLS-Multi-NA-Feed-PLA-NA-NA-HandTools_PLA&cm_mmc=Shopping-B-F_D25T-G-D25T-25_1_HAND_TOOLS-Multi-NA-Feed-PLA-NA-NA-HandTools_PLA-71700000034127224-58700003933021546-92700031755124841&gclid=CjwKCAiAt9z-BRBCEiwA_bWv-PstIaMIhoHdrCIUmMb4KY1XWg9m1g3ygoP5GVapaPbB1VTqmLDoBxoCeCQQAvD_BwE&gclsrc=aw.ds
Posted on: 2020/12/14 20:52
|
|||
|
Re: Update on 356 CI Block
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I have drilled and tapped plugs with a left hand threaded tap then screwed in a left hand threaded bolt which allows you to put a socket on it to remove the plug.
Posted on: 2020/12/16 8:13
|
|||
|
Re: Update on 356 CI Block
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Did you make any progress?
Posted on: 2020/12/22 18:21
|
|||
|
Re: Update on 356 CI Block
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Finally able to remove ALL oil galley plugs. The plugs with the shallow square had to be drilled out. I carried the block to my buddy's machine shop and we were able to remove them.
He stated they were the toughest to remove in his 25 years! While in his possession, I had him check the piston clearance as the block had been bored .030 over. I'm also waiting on the main bearing clearances as we are using the original crank with the new block. After next week, I'll be able to start the rebuild. Thanks again for all the help! Merry Christmas and a safe and Happy Holidays to all.
Posted on: 2020/12/24 16:23
|
|||
Steve P
Forest, Va 1929 645 Dual Cowl Phaeton 1937 120C Conv Coupe 1940 1389 Conv Coupe 1940 1377 Super 8 160 Conv Sedan |
||||
|