Re: Wipers/washers brake hoses
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Believe you mean 32nds instead of 23rds for the fractions??
The Trico instructions and the Packard rewrite of the same mentions sizes in standard fractions of 1/4, 3/16. and 1/8 for the washer tubing. The fittings are exactly those sizes but the barbs are slightly larger so you get a decent fit on the hose. I used the 1/32 less on all because that was what I could easily get locally in plain rubber vacuum rated hose. While connections were maybe a bit tight on fittings with barbs, it paid off on the steel tubing from vacuum sources where there are no barbs. The 7/32 made for a nice snug fit on those. For the sweep control that is a tad smaller. 3/32 works but 7/64 seems about right. Both ODs are smaller than old stock hose so going thru the grommet might leave a bit of opening. I tried straight 3/8 on the brakes and thought it was too easily pulled off because there are no barbs on those fittings. As you mention, modern hose seems a bit less in OD than the old stuff. Maybe made of a better material or just going cheap but original wire clamps were not much help in securing the hose. I changed it to the 11/32 hose for a tighter fit and then used a modern wire clamp. I have a couple of balance valves and they appear to be straight diecast zinc. No yellowish coloring I can see. Here is the Trico illustrations for a 54 and Packards rewrite for 55 for comparison. Tubing sizes appear to be identical. Attach file: ![]() ![]() ![]() ![]()
Posted on: 2014/11/30 13:39
|
|||
Howard
|
||||
|
Re: Wipers/washers brake hoses
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Ok. Thanks Howard. You, Kev, O D and others are a great help always with good info and advice. I saw the latter diagram but no size chart with it. Never thought to look at a 54 manual. Interesting the 55 does not show the tiny "short stroke" hose. I guess the same 1/8 used under the dash for fluid delivery. All I have avail on that is a very soft rubber. Not sure if it will collaps for the vacuum.
If I test the balance valve it seems to operate in the reverse manner I suspected. I will post pics. and desc. It does have a goldish apperance but I saw on some other posts a "varnish" or clear used on some parts that yellows over time. could be the same? Sorry for the mis type. I was referring to the 7/32 and 5/32. they seem to come in 32nds or 64th.
Posted on: 2014/11/30 20:28
|
|||
|
Re: Wipers/washers brake hoses
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
I tried to get some close up shots. you can see the gold color the best on the hose nipple leading to the wiper mtr. Also note the very small lettering on the fittings designating manifold, v p, and washer. As i understand it, the balance valve should let vac pass from both inlets to both outlets which it does. It was there to "close off" the manifold inlet when under WOT there is no manifold vac and allow the vac pump to supply the wiper. When I test- it does that exact function very well but opposite. If there is no vac from the pump! It closes that port and allows a sealed vacuum passage from the manifold to the outlets. see test pic. I was hoping to verify operation and install back on the car without opening it up. Anyone ever tested theirs?
Posted on: 2014/11/30 21:02
|
|||
|
Re: Wipers/washers brake hoses
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
In the pic above with a vac pulled on the "man" inlet fitting and the "V P" open to atmos. vac will be applied and held to the outlets. Should the same be true pulling a vac on the "v p" fitting and the "man" open to atmosphere?
Posted on: 2014/11/30 21:15
|
|||
|