Re: 1940 160 Gauge Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Its possible it's just stuck. My '39 was pinned the other way and when I took it apart, it was somehow adhered with what looked like a little ball of paint to the top end of the travel. Yours may or may not be that; main reason I weighed in is I have a 1940 gas gauge/ammeter gauge cluster that I got on Ebay. The actual gauges were the same as my '39, although the front bezel and lettering was a bit different. If you find you're in need, PM me.
Posted on: 2018/9/14 18:55
|
|||
'If you think you can, or you think you can't - you're right!' Henry Ford.
1939 Packard Six, Model 1700 |
||||
|
Re: 1940 160 Gauge Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Oh, and I forgot to mention, again, if it's the same as mine, it CAN be removed from the back and the studs are fixed.
Posted on: 2018/9/14 18:57
|
|||
'If you think you can, or you think you can't - you're right!' Henry Ford.
1939 Packard Six, Model 1700 |
||||
|
Re: 1940 160 Gauge Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
If it doesn't return to 0 with the key off, just try tapping on it with the palm of your hand several times. I know, it sounds like car repair by hammer.
Its natural position is 0. There's only one reason why is reads Discharge (unless it's stuck), is because it has a major discharge. Using a mirror, see if the wiring looks okay, then it's stuck. If it's really broken, I don't think you have to remove the nuts, just loosen them enough so you can wiggle the ammeter off. The ammeter doesn't have holes for the studs, just crescents. It will be a lot easier to put back.
Posted on: 2018/9/15 13:56
|
|||
|
Re: 1940 160 Gauge Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Hey Friartuck,
Joe makes a good point re not removing the nuts entirely, at first, anyways, because again, if the gauges are the same as mine, and it sounds like they probably are, if I remember correctly, only one end of the gauge had crescents and the other had full holes. If you loosen them all off, it will be easy to see which is which. I think it is the outside two with full holes while the inside two 'share' studs with the speedo. (again, if my memory serves me correctly) I ended up removing my front seat bottom and putting a piece of foam against the firewall for my head and laying in there on my back with one of those harness head lamps on and I was able to see quite well. I found hand-nut drivers worked very well to hold the nut while getting it in to place to start the threads. Don't forget those wires are plenty hot, even with the key off! Good luck, Chris
Posted on: 2018/9/17 0:23
|
|||
'If you think you can, or you think you can't - you're right!' Henry Ford.
1939 Packard Six, Model 1700 |
||||
|
Re: 1940 160 Gauge Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
This is from my spare parts either for a 40 or 41? Cannot remember
Posted on: 2018/9/17 0:39
|
|||
|
Re: 1940 160 Gauge Removal
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Other side. How do you people attach more than one picture at a time?
Posted on: 2018/9/17 0:40
|
|||
|
Re: 1940 160 Gauge Removal
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
1940.
Posted on: 2018/9/17 6:03
|
|||
|