Happy Easter and welcome to Packard Motor Car Information! If you're new here, please register for a free account.  
Login
Username:

Password:

Remember me



Lost Password?

Register now!
FAQ's
Main Menu
Recent Forum Topics
Who is Online
107 user(s) are online (69 user(s) are browsing Forums)

Members: 2
Guests: 105

r1lark, Jim in Boone, more...
Helping out...
PackardInfo is a free resource for Packard Owners that is completely supported by user donations. If you can help out, that would be great!

Donate via PayPal
Video Content
Visit PackardInfo.com YouTube Playlist

Donate via PayPal



(1) 2 »

1951 Exhaust support #426241
#1
Not too shy to talk
Not too shy to talk

RKS
See User information
I am getting exhaust support part #426241 for my 51 300, I know the one end of the support will attach to the flywheel housing but was curious to how and what attaches to the other end (this is a used part)

Attach file:



jpeg  (386.55 KB)
123565_5f50e664d06f8.jpeg 1200X1600 px

Posted on: 2020/9/3 7:46
 Top  Print 
 


Re: 1951 Exhaust support #426241
#2
Forum Ambassador
Forum Ambassador

HH56
See User information
My question is that photo of a 51-3 support or is it a 54 item.

In this photo of a 53 engine compartment there looks to be a tab welded to the exhaust pipe the end of the support would bolt onto. That would also hold with the hardware associated with the 51-3 support since there is mention of a second bolt to the pipe -- 51 had a 5/16" bolt plus a nut & washer while the 52-3 went to 1/4".

In 54 there was something called a loop associated with the support instead of a bolt. If that is a stock unmodified support in the photo, the way the bend is made on the support it almost looks like the 90 degree portion lays on the top of the exhaust pipe and some kind of clamp or loop goes around both to hold them together. Perhaps that change was done to cut costs since there was no need for the factory or dealer or aftermarket muffler shop to weld on a tab in a precise location. You could probably duplicate the function of the loop by using a common exhaust pipe clamp.

Attach file:



jpg  (62.73 KB)
209_5f50fbb86fa58.jpg 640X480 px

Posted on: 2020/9/3 9:23
Howard
 Top  Print 
 


Re: 1951 Exhaust support #426241
#3
Not too shy to talk
Not too shy to talk

RKS
See User information
Hi Howard thanks for your reply and the pic it helps greatly I found this other information also, I haven't received the part yet but I figure it was only $5 so hopefully I will figure it out now.

Attach file:



jpeg  (57.13 KB)
123565_5f510441a06cf.jpeg 1153X736 px

jpeg  (33.55 KB)
123565_5f510458a8da3.jpeg 808X484 px

Posted on: 2020/9/3 9:57
 Top  Print 
 


Re: 1951 Exhaust support #426241
#4
Home away from home
Home away from home

Let the ride decide
See User information
Plate 97of parts book,
group 6.1025 is that the part?

http://www.packardinfo.com/xoops/html/downloads/partslist4854/48-54_Plates.pdf

Posted on: 2020/9/3 10:06
 Top  Print 
 


Re: 1951 Exhaust support #426241
#5
Forum Ambassador
Forum Ambassador

HH56
See User information
I was thinking about the visible tab on the 53 exhaust pipe as to whether it is a single tab welded on or a wrap around. Unfortunately the photo is small so there is not much detail and the unraveled duct hose hides enough that you cannot see if there is possibly another tab with a hole behind the loops.

If there is another tab that would make it a wrap around sort of clamp where both halves bolt together with the support in the middle or side. A wrap around clamp is sort of what the 46-50 models used and those clamps could be a pain to spread enough get on the pipe and then pulled together again and held so a nut could thread onto the bolt.

Posted on: 2020/9/3 10:10
Howard
 Top  Print 
 


Re: 1951 Exhaust support #426241
#6
Not too shy to talk
Not too shy to talk

RKS
See User information
Hi thanks for the info it all helps

Posted on: 2020/9/3 10:25
 Top  Print 
 


Re: 1951 Exhaust support #426241
#7
Not too shy to talk
Not too shy to talk

RKS
See User information
I follow you might have to spot weld a bracket on, its not causing me any problems without it and not sure of its purpose I just like to try and keep the old Packard engineers happy since they had a reason and spent the time on it lol

Posted on: 2020/9/3 10:27
 Top  Print 
 


Re: 1951 Exhaust support #426241
#8
Home away from home
Home away from home

Ross
See User information
Huh? The fabric end bolts up high on the bell housing with a short 3/8 bolt and washer. The lower end bolts onto the selfsame lower bellhousing bolt that supports the road draft tube. The hole closest to the bend bolts to the tab on the exhaust pipe. Having this piece on the car keep your exhaust pipe-to-manifold gasket from certain premature death.

Posted on: 2020/9/3 20:37
 Top  Print 
 


Re: 1951 Exhaust support #426241
#9
Forum Ambassador
Forum Ambassador

HH56
See User information
Ross, that makes sense and a lot like the 46-50 piece. What or where is the loop they call for in 54 positioned or does that take the place of the welded on tab?

Posted on: 2020/9/3 20:43
Howard
 Top  Print 
 


Re: 1951 Exhaust support #426241
#10
Home away from home
Home away from home

Packard Don
See User information
That may explain the different part number for 1954. Some years ago I asked Waldron and they didn't know either and had no 1954 template. I wonder what other differences there were in the exhaust for 1954.

Posted on: 2020/9/3 20:48
 Top  Print 
 




(1) 2 »




Search
Recent Photos
Photo of the Day
Recent Registry
Website Comments or Questions?? Click Here Copyright 2006-2024, PackardInfo.com All Rights Reserved