Re: 1955 Horn Button removal
|
||||
---|---|---|---|---|
Forum Ambassador
|
Yes, the rubber "O" ring provides the friction that holds the emblem in place. You should be able to use something like the edge of a plasticware picnic knife to get the separation started.
Posted on: 2021/6/7 18:19
|
|||
|
Re: 1955 Horn Button removal
|
||||
---|---|---|---|---|
Forum Ambassador
|
The emblem is normally held only by friction provided by the O ring. While it is snug it usually will come out with some gentle tugging. HOWEVER, there is a dense foam rubber block for a cushion under the emblem. There should be a piece of a wax like paper between the cushion and emblem but if the emblem was off and the paper was left out at some point then if the old rubber has deteriorated and turned soft it is almost like melted rubber and a very good glue.
If that has happened there is not much you can do except use something soft like a stiff wood or plastic object under the emblem and try to GENTLY pry it loose at a few spots. Wider objects will spread the load over more surface and minimize chances of a piece of the emblem edge chipping off but there are no guarantees.
Posted on: 2021/6/7 18:24
|
|||
Howard
|
||||
|
Re: 1955 Horn Button removal
|
||||
---|---|---|---|---|
Home away from home
|
I've been running a stiff metal putty knife around under it and prying hard to where the lip is likely to break off and it's not budging in the slightest.
Posted on: 2021/6/7 18:40
|
|||
1942 Clipper Club Sedan
1948 Custom Touring Sedan (22nd Series) 1955 Patrician Sedan 1955 400 Sedan |
||||
|
Re: 1955 Horn Button removal
|
||||
---|---|---|---|---|
Forum Ambassador
|
I would find something other than the putty knife. As to something else to try, I hate to suggest this because I don't know if it has ever been done before. It is the least likely to cause problems that I can think of though.
See if you can get the end of an application tube from a spray can of WD-40 at a few spots in the crack and give it a couple of liberal squirts. Use a rag wrapped around the area to try and keep it from spraying all over the place or dripping on the upholstery. Maybe do this a couple of times over a few hours and then try the gentle prying. WD-40 is often used to soften adhesives on painted surfaces so it is very gentle and should not affect paint or even the plastic emblem like other solvents can. If you wanted you could try it in a hidden spot on the steering column just to make sure there is no paint damage.
Posted on: 2021/6/7 18:52
|
|||
Howard
|
||||
|
Re: 1955 Horn Button removal
|
||||
---|---|---|---|---|
Home away from home
|
Quote:
I tried silicone spray with the tube/straw but that didn't seem to help. I'll keep working at it.
Posted on: 2021/6/7 19:07
|
|||
1942 Clipper Club Sedan
1948 Custom Touring Sedan (22nd Series) 1955 Patrician Sedan 1955 400 Sedan |
||||
|
Re: 1955 Horn Button removal
|
||||
---|---|---|---|---|
Home away from home
|
Found my set of trim removal tools which are a very hard plastic and was able to use them as wedges to break it free without breaking off a lip.
The O-ring was only partially in the groove and the horn button must have been forced in. Consequently the O-ring was deformed. After removal of the wheel I was able to lubricate the upper steering shaft bearing, which was my goal. It had high stiction which made driving it annoying as you couldn't use gentle pressure to keep the car in a straight line, but it would break free in opposing directions leading to erratic driving. I had to use the tool to work the deformed O-ring into the groove along with a light film of silicone grease as the button went in to get it seated properly but mission accomplished. Thanks for the help. I've had the '48-'50's apart many times (the button is a press and turn) but never before the '55-'56 so wanted to make sure I wasn't doing something wrong.
Posted on: 2021/6/7 20:13
|
|||
1942 Clipper Club Sedan
1948 Custom Touring Sedan (22nd Series) 1955 Patrician Sedan 1955 400 Sedan |
||||
|