Re: Oil ports on starter, generator and water pump 1941 engine
|
||||
---|---|---|---|---|
Forum Ambassador
|
On the starter and generator, just a few drops. The 55-6 manual says 5-10 on the generator and suspect earlier years would be the same. Use the lower amount on the rear or brush end cup because too much oil there can work its way out and deposit on the commutator causing issues. Don't forget the grease cup for the distributor shaft and bushing needs to be packed with cup grease and gets a half turn when you do a lube.
Others will need to comment on the water pump as the postwar pumps I am more familiar with have sealed bearings so no routine oil requirements.
Posted on: 2023/6/17 12:43
|
|||
Howard
|
||||
|
Re: Oil ports on starter, generator and water pump 1941 engine
|
||||
---|---|---|---|---|
Just popping in
|
Thanks Howard!!
Posted on: 2023/6/17 13:15
|
|||
|
Re: Oil ports on starter, generator and water pump 1941 engine
|
||||
---|---|---|---|---|
Home away from home
|
Regarding the Distributor, I recommend removing the grease cup and cleaning out the old grease using a fine wire to try and include the fine hole to the bushing shaft, mine was akin to bee's wax! Replace it with new 'cup grease' which in today's parlance is NLG1 Grade 2 All Purpose Grease. Here in Canada it is available through Motomaster in Canadian Tire Stores. A search in your area will surely find its local equivalent. The image below shows it in a mini tube I got which will last a couple of life times!
Bob J.
Posted on: 2023/6/17 13:30
|
|||
|
Re: Oil ports on starter, generator and water pump 1941 engine
|
||||
---|---|---|---|---|
Just popping in
|
Thanks Bob!
I just found the port and it had a little grease but not much. Will look for the little hole. I dont see the image but will search out your suggestion.
Posted on: 2023/6/17 13:59
|
|||
|
Re: Oil ports on starter, generator and water pump 1941 engine
|
||||
---|---|---|---|---|
Just popping in
|
Your image popped up thanks!
Posted on: 2023/6/17 14:00
|
|||
|
Re: Oil ports on starter, generator and water pump 1941 engine
|
||||
---|---|---|---|---|
Just popping in
|
Do i fill the cup up? Or 1/2 or ??
Posted on: 2023/6/17 14:03
|
|||
|
Re: Oil ports on starter, generator and water pump 1941 engine
|
||||
---|---|---|---|---|
Home away from home
|
Yes, you fill the cup. The owner's Manual for my '37 120 instructs to turn the grease cup 1 turn every 2000 miles, along with 1 drop of oil to the breaker arm pivot, a few drops on the wick under the rotor and a small amount of Vaseline on the breaker cam. The instructions on my 58 Pontiac were the same so they should apply to your 41 as well but you can find your manual on this site to verify.
So, the small hole I refer to is at the bottom of the funnel shaped fitting the cup screws onto. It can be removed using a 7/16" wrench. Clean it right out and be sure to go right through the small orifice that guides the grease into the bushing surface. Leave it empty and screw the full cup onto it until you see grease exiting the bottom hole. Then refasten it to the distributor and do the one turn to allow for the first application of new lubricant. Bob J.
Posted on: 2023/6/17 15:36
|
|||
|
Re: Oil ports on starter, generator and water pump 1941 engine
|
||||
---|---|---|---|---|
Home away from home
|
Palmer. Wasn't that Michael Caine's character in the Ipcress File?
HH56 right as rain as always. Too much oil on the ones he cautions can get on the brushes. A machinist friend reminds us to use 20 or 30W nondetergent for such oiling duty. In fact, when he and our mutual auto/aero/mechanic/machinist/pilot friend replaced their compressors, they noted such suggested for them, and this was circa 1980. For the distributor grease cup, we use the black molybdenum/graphite; StaLube, Texaco EP, etc. One of the Seven Sisters petrochemists years ago told us such grease a factor of eight-fold better than the orange fiber grease of the '40s through early '70s. Had that stuff been around in the day, lotta Packards and other old cars'd still be on the road. Zen and the Art of Packard Maintenance: Rather than a turn every 1,000 miles, give mine half a turn every 500. Overkill, of course.
Posted on: 2023/6/17 16:51
|
|||
|
Re: Oil ports on starter, generator and water pump 1941 engine
|
||||
---|---|---|---|---|
Just popping in
|
Wow, thanks. In the meantime i took the cap off, cleaned it out good and used a small stainless wire to clean out the cup and hole, and repacked it. but it looks easier in your pic when its on your bench! I know i’m dense, but i dont understand turning the cup every 2000 miles. Of course, i dont put even 200 miles a year on it ….so maybe it doesn't matter!.
Posted on: 2023/6/17 17:48
|
|||
|