Re: Paint Metal Flakes
|
||||
---|---|---|---|---|
Just can't stay away
|
For 1936 120B there were Five colors that used metallic.
Duco 202-31473 Gunmetal Light Metallic Color Scheme A 202-31474 Almond Green Metallic " " J 202-31475 Golden Tan Metallic " " P 202-31476 Trianon Green Metallic " " Q 202-31482 Tuscan Red Metallic " " Z Hope this helps you out. I think Metallics were used in the 20,s as well. Most Packard colors were very conservative or subdued ,not flashy unless special ordered . The scheme letters referred to the pin stripe color and wheel color.
Posted on: 2020/6/11 10:34
|
|||
|
Re: Paint Metal Flakes
|
||||
---|---|---|---|---|
Forum Ambassador
|
One thing I have read or seen discussions on forums is the material used for the metal flakes. As I recall the consensus is metal flakes were of a different size and material in the Packard days and todays flakes give quite a different look.
Posted on: 2020/6/11 10:49
|
|||
Howard
|
||||
|
Re: Paint Metal Flakes
|
||||
---|---|---|---|---|
Home away from home
|
The problem with modern paints is that the metal flakes are WAY WAY too large for what is correct. Knowledgeable restorers are sifting their paints. The correct flakes should be a mere fine powder, and should be BARELY discernible in the paint when looking at it.
Posted on: 2020/6/11 10:56
|
|||
West Peterson
1940 Packard 1808 w/Factory Air 1947 Chrysler Town and Country sedan 1970 Camaro RS packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=4307&forum=10 aaca.org/ |
||||
|
Re: Paint Metal Flakes
|
||||
---|---|---|---|---|
Home away from home
|
Thanks guys for the input, but here is the dilemma
I have to choose a paint for my car the car is 1936 120B conv/coupe, it was a copy of Tuscan red and it will remain red because the wheels, fire wall, door jams are red, in good shape. Trying to figure out whether to put flakes in the paint or not. I don't mind a little flashy but I don't want what looks like a Hot Rod. Car has white pinstriping Any opinions? Thanks in advance W
Posted on: 2020/6/11 12:26
|
|||
|
Re: Paint Metal Flakes
|
||||
---|---|---|---|---|
Forum Ambassador
|
Just my opinion. Unless you are able to use a ball or pebble mill or an attritor to reduce the size of the metal flake component before incorporating it into the paint formulation (or source an extremely fine particle size metallic component), I'd go with a nonmetallic paint.
Posted on: 2020/6/11 15:40
|
|||
|
Re: Paint Metal Flakes
|
||||
---|---|---|---|---|
Home away from home
|
I don't recommend using a ball mill to reduce the aluminum flake size. Aluminum flake doesn't snap, it folds and wads up. Without the plate shape, it doesn't flash,but it grays out the color.
Siberline is the major producer of metallic flake for paint and coloring - get a small size flake if you want to go metallic.
Posted on: 2020/6/11 16:18
|
|||
|
Re: Paint Metal Flakes
|
||||
---|---|---|---|---|
Home away from home
|
I have a friend in Austin who painted his 30 Packard with the correct metallic blue. They got the metallic powder from the Phillipines where it is used in women's makeup. That stuff is so light it will almost float out of the jar. Contact Mike at Crossroads Restorations for more info.
Posted on: 2020/6/12 11:28
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: Paint Metal Flakes
|
||||
---|---|---|---|---|
Home away from home
|
you can normally buy it with a choice between a couple of "wetting agents" to tame the dusty/static problem. But choose a wetting agent compatible with the paint in this case! Also, I'd avoid grades with coating on the aluminum for the same reason.
Posted on: 2020/6/12 13:10
|
|||
|
Re: Paint Metal Flakes
|
||||
---|---|---|---|---|
Home away from home
|
Find the Ditzler and/or Dupont paint chips in the Packard Literature section for 1936. Get the formula for Tuscan Red. Contact PPG industrial/automotive paints and ask them to translate the formula to modern materials. They will send the formula to your paint shop, not to you. Have the shop shoot a fender for approval. PPG bought Ditzler, so they know how to translate the formula. They know the correct amount and size of reflective material. My 1940 color has a combination of small and medium flake.
You can make a product inquiry here.corporate.ppg.com/Contact.aspx Tell them the contact info for your paint shop.
Posted on: 2020/6/12 15:21
|
|||
|