Packard Forum Index » Project Blogs

Thursday 20th August 2009

Wade had asked me a couple of days ago to mount a hose saddle on the end of the bench, so the air hose could be coiled up instead of it hanging on a hook. Seemed like a 5 minute job but won't go into the details except to say it took about an hour instead of the expected 5 minute time frame.

Then I turned to finishing off scraping the POR-15 run-through from the top of the remaining running board. While I was doing that Wade was servicing his Commodore dual-cab ute. The ute will be used to tow the trailer with the '34 body on Tuesday so it received a very thorough service to ensure it was in shape for the tow ahead of it. Wade is also in the process of trying to run down a set of standard sized big-end bearings for Big Red and he believes he has lead on a set from a fellow PACA member.

Also started to clean up the NOS accelerator pedal from the "Flackmaster", but shelved using the wire wheel when I realised the rubber surface was bonded to the pedal itself. (David, just demonstrating what many years of shelf life can do to parts.) Will clean up the rest of the surface rust, with a small wire brush and paint with POR-15 next week, when I'm back at the workshop next week.

That was it for the day as there were no simple and/or menial tasks left which I could perform. So went home for lunch amazing Kath in the process as she usually doesn't see me that early on the day's I go to the workshop.

Attach file:

---

  (37.30 KB)


  (37.25 KB)


  (31.39 KB)


  (28.46 KB)


  (31.55 KB)


  (22.93 KB)


  (22.67 KB)


  (21.72 KB)

Back in post #186 I included the pic below. This was taken back in 1980 when Robert Sacchi was in Sydney promoting the movie he starred in, "The Man with Bogart's Face".

http://www.videodetective.com/?publishedid=2881

Harvey and his then Packard, a '38 120 Sedan with O/D, was used to ferry Robert Sacchi around Sydney for radio and TV interviews, promotions and the film's opening night.

I've also included a pic of Harvey taken today at Eastern Creek.

Attach file:

---

  (41.39 KB)


  (37.78 KB)

Monday 24th August 2009

Only spent about 5 minutes at the workshop today and there I found Wade in the process of removing Old Blue's front clip to have the radiator cleaned, checked, repaired and tested. It's had a bit of a leak for some time and with Wade taking her on a couple of thousand miles round trip in three weeks time decided he's better off get it fixed now rather than have a problem occur during the course of his journey.

And tomorrow, the big day! Down to Helensburgh to pick up the '34's body!

Attach file:

---

  (43.55 KB)


  (18.58 KB)

Tuesday 25th August 2009

Well, the big day, and the '34's body beautiful was to be united with it's lonesome chassis. But !!!!!
Because of high winds, overnight and this morning, with trees and branches down and roads blocked the trip was cancelled! It's re-scheduled though for Thursday but, because of other commitments, I can't make it so Wade has strict instructions to take many, many pic's.

At the workshop I found Wade had removed the front clip from Old Blue and taken the radiator to JJ Smiths yesterday and it's expected to be ready Friday. Wade was also taking the opportunity, while access was readily available, to undertake replacement of Old Blue's exhaust manifold. The manifold has a crack in the flange where it bolts to the exhaust pipe. Although Wade had it repaired about 5 years ago it wasn't successful and with a good exhaust manifold obtained from PACA member Fred D, also known as "Pepe" because he comes from south of the border, now was the time to replace it. Wade had already disconnected linkages and lines and removed the air-cleaner and carb so removing the intake and exhaust manifolds should be pretty straight-forward, shouldn't it? Well No! Why? Because it's RHD and the steering column only has about 1/8" between it and the manifold hot box, and that's after the column has been flattened to clear the hot box! So the steering box is unbolted from the chassis and from under the dash, the pitman arm disconnected from the sector shaft and the steering box and column swung up and outside the chassis to give enough clearance to remove the manifolds. Once out, while Wade cleaned up the surfaces of the replacement exhaust manifold, I cleaned up the block surface of old gasket. All went back together accompanied with a liberal application of manifold sealer to ensure against leaks.

There won't be any posts at least until Friday. Then I'll be able to provide pic's of the '34's body, and the radiator and front clip will be able to go back on Old Blue.

Attach file:

---

  (40.58 KB)


  (33.87 KB)


  (23.37 KB)


  (19.77 KB)


  (26.51 KB)


  (34.96 KB)


  (41.06 KB)


  (40.88 KB)


  (22.70 KB)


  (41.39 KB)


  (29.36 KB)


  (42.93 KB)


  (33.21 KB)

Mal, thanks for the close-up photo of the full flow oil filter on the '38. I am impressed with your memory and recall of my post to your blog some time ago. Could you also get for me (and others) a close-up view of the oil lines connections to the oil pump cover plate? It would be an interesting project to have a full flow oil filter on the 115C. Too hot to work in the garage these days. Austin, Texas is about to set a record for the number of days of temperatures at 100F and above. We are at 62 and the record is, I believe, 69 set in the 1920s. It is getting a little tiring. It is our "Minnesota Winter". I blame Al Gore. Take care . . .

Friday 28th August 2009

Before going to the workshop rang the guy in Victoria who bought my '38 sedan at auction last month. I'd tried to email him a couple of times but they kept bouncing back, so direct contact was required. Turns out the guy, Peter, has Mercedes and when I asked him why he bought the Packard said he saw it at the auction and liked it! Fair enough. Had it trucked back to Victoria and has been driving it, being impressed with the car itself and the engine. I was able to give him some info about it and he told me he is getting a new radiator because of it's propensity to run hot. Invited Peter to join PACA(Packard Automobile Club of Australia) and mailed him a copy of "The Packardian" our bi-monthly magazine, a reprint '38 owner manual(there was one in the glovebox when it went to auction!) and some membership forms.

At the workshop arrived just in time to see the guys, Wade, John, Rick and Graham starting to re-arrange things so the '34's body could be re-positioned. Yesterday Wade, accompanied by PACA member Peter L had taken the car trailer to Helensburgh and picked up the body and other parts from the paintshop. They still have some more parts to paint including the fenders, hood and grill shell. I started taking pic's and Wade promptly stuck his camera in my hand with instructions to get some pic's for him. So there I was, a camera in either hand, snapping away usually alternatively with my camera and then Wade's camera. Fortunately the guys had it all under control so my in-expertise wasn't required and I continued my work as official photographer. The body ending up positioned between the '34 chassis and the engineless Big Red up on it's jackstands.

Next joined Wade in his Ute for the trip over to Marrickville to JJ Smith's to pick up Old Blues radiator. Turns out it was about 20% blocked so there will be a marked improvement in cooling efficiency when it goes back in. On the way to JJ Smith's discussed the projects at the Workshop and my want for the Coupe's engine to be overhauled. They are the 1) '34 - long term restoration, 2) '37 120 - re-install radiator and front clip and will be able to do in the next few days, 3) '37 Super 8 - rebuild engine and re-install together with radiator and grill. Wade had received a set of big-end bearings on the weekend at Shannon's Eastern Creek display day but it turns out they don't fit! So until some replacements can be sourced Big Red's not going anywhere. 4) '39 110 - remove old engine and install re-built engine sitting on floor shop still need a few parts but should be pretty straightforward and 5) '41 120 - rebuild engine and clutch, trans and O/D as required, but the '41's work will be dependent on what's happening with the other four.

I'd also phoned Peter, at Rhino linings earlier in the morning, and learned if I could get the '41's running boards to him today they'd be ready early next week. So with photographic responsibilities completed that was my final Packard destination for the day.

Attach file:

---

  (25.69 KB)


  (27.02 KB)


  (30.88 KB)


  (35.62 KB)


  (35.87 KB)


  (40.29 KB)


  (31.71 KB)


  (21.21 KB)


  (26.97 KB)


  (35.72 KB)


  (31.87 KB)


  (24.88 KB)


  (33.22 KB)


  (33.22 KB)


  (23.45 KB)


  (20.35 KB)


  (30.17 KB)


  (21.78 KB)


  (23.10 KB)


  (22.60 KB)


  (16.02 KB)


  (24.30 KB)


  (24.13 KB)


  (27.58 KB)


  (16.02 KB)


  (19.64 KB)


  (14.12 KB)


  (18.75 KB)


  (33.28 KB)


  (36.63 KB)


  (22.98 KB)

Hi Mal,
The 34's starting to look great again. You two are certainly doing some good things resurecting old Packards.
Any chance of a Pic or two of the heat riser valve either side of the exhaust manifold under the carb?
Speak to you again soon in regard to the rear lower shock mount details
Uh roo
Terry

Terry, didn't I send you a sketch of the heat riser valve for the 1934 Eights? If not I can add it here.

Mal, this project never seises to amaze me,it is interesting to read what happens one at the other side of the world

Quote:
Terry,

Don't confuse me with what I'm posting here. All the credit should go to Wade, I follow along and pass spanners, scrape dirt and grease, paint parts and take pic's.

Will be at the workshop this morning, Saturday, so will get the pic's you want. And JW I'll get yours too!

And I haven't forgotten the rear lower shock mounts. I'll get under the '34 chassis soon and measure it up for you.

And Steve(Hardtop),

You're amazed?

I'm the one who's constantly amazed!