Re: Packard aluminum head
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Jack, what would you be looking for in a V8 intake?
Posted on: 2014/6/29 16:10
|
|||
|
Re: Packard aluminum head
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
HH56, the aluminum will be slightly thicker especially in the deck surface to help it hold its shape and seal. it may be a bit taller to hold more water but unless you have a stock one sitting right next to it, it would likely be tough to tell. The fins would be cast in and similar to an Edmunds piece. I can ask if he could optionally mill the fins off but it would likely be an up-charge. The rounded look can be achieved with a CNC operation but the head would need to be either sand blasted or polished to take away the machines finish.
Posted on: 2014/6/29 22:50
|
|||
|
Re: Packard aluminum head
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Dual quad on the v8 I'm sure. Unless there is a way to cram 3 quads on there ....muuuhahahahahhhahahaha !!!
Posted on: 2014/6/29 23:18
|
|||
1937 Packard 138-CD Deluxe Touring Limousine
Maroon/Black 1090-1021 [url=https://packardinfo.com/xoops/html/modules/registry/View.php?ID=232]1955 Packard |
||||
|
Re: Packard aluminum head
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Quote:
Tri-Power? (o{}o)
Posted on: 2014/6/30 11:45
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: Packard aluminum head
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Tri-power would be cool and dual quad would be nice as the original dual quad manifolds are super hard to come by. anyone want 6X2 or 8X2? lol
Posted on: 2014/6/30 11:51
|
|||
|
Re: Packard aluminum head
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
He can do a separate head without fins for people looking for an original equipment look. Price should be the same (1200-1500) I would need to know if a faithful reproduction was wanted or just a head that was not finned.
Posted on: 2014/6/30 11:56
|
|||
|
Re: Packard aluminum head
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Restorers will want a head identical in appearance to stock, complete with casting numbers etc.
Rodders will want finned heads, as jewel like and finely finished as you can make them. Incidentally the 54 Packard 8.7:1 head is the highest compression ever in a stock flathead, and they had to do every trick in the book. I doubt you can go higher without cutting off breathing. This much compression may require high test, 92 octane fuel.It is not comparable to a modern OHV or OHC, 8.7:1 engine, which has a thermodynamic advantage.
Posted on: 2014/6/30 12:06
|
|||
|
Re: Packard aluminum head
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
8.7:1 would definitely be the upper limit of of compression in a flathead. and I would venture a guess that high test gas would need to be used. if anyone has pictures of the factory aluminum head that they could send me, something with the details of the casting marks etc I will forward them to the guy making the patterns and see what he can do. The heads will likely be sent out in a cast finish as polishing is a long tedious process and would raise the cost quite a bit but I will double check and get back to you.
Posted on: 2014/6/30 12:19
|
|||
|
Re: Packard aluminum head
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
If you are serious about doing this someone should be able to send you a damaged (no longer usable on a car) head for reference.
The stock head would be "as cast" and I expect they were painted when the 54s were new. Finned heads are usually "as cast" too but if you can do a finer casting than they did in 1954, that is all to the good. I don't think a finned head with the fins milled off would be any good to a restorer, as it would still not look original.
Posted on: 2014/6/30 15:07
|
|||
|