Re: 115c Generator
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
I should have one....I will look tomorrow, already locked the door on the generator shed...
DAF
Posted on: 2015/5/16 20:17
|
|||
|
Re: 115c Generator
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Thank you Flackmaster! Please ket me know.
Bob
Posted on: 2015/5/17 13:09
|
|||
"Vision without execution is just hallucination"
|
||||
|
Re: 115c Generator
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Hi Bob,
I looked this morning with the aid of a magnifying glass at the generator on my 37 115c. The Model number is 948U and the serial number is 20554. I hope this will help you.
Posted on: 2015/5/18 7:07
|
|||
|
Re: 115c Generator
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
OEM parts for a 1937 115C were generator and regulator 948U and 5827 if Delco-equipped, GCJ-4801A and VRD 4001A if AutoLite.
Posted on: 2015/5/18 7:53
|
|||
|
Re: 115c Generator
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Thank you Corsaseven and Owen Dyneto for the information.
I'm hoping that Flackmaster may have something in his inventory. I think that the regulator on the cat may also be wrong also as I have a fourth wire in the new harness. Bob
Posted on: 2015/5/18 11:39
|
|||
"Vision without execution is just hallucination"
|
||||
|
Re: 115c Generator
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
Hi,Bob the original regulators had 4 terminals but the correct replacements had three(they just told you to tape up the extra wire. I will check but I think it was a ground terminal/wire that they eliminated.
Posted on: 2015/5/18 12:00
|
|||
|
Re: 115c Generator
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
I have three - autolite GCJ-4801A, used, no history, Delco 948U, used, streetrod takeout, and a NORS replacement unit, which I would have to look closer at to see if it is a Delco or Autolite unit....150 ea, your choice. If it were me, it would be a coin toss between the Autolite and Delco, both are pretty easy to service, or the NORS unit which should be ready to go. OH, wait, now I remember why I have the new unit - because the guy who shipped it to me packed it like crap and broke/bent the pulley, so you'd have so source a pulley from a shop (they are all the same size) I do not have a Delco regulator, only autolite VRD's, so that may matter if you don't have a regulator.
Note that I am headed off to the Euro-Packard Rally tomorrow, so if you want something shipped, your prompt reply would be necessary. DAF
Posted on: 2015/5/18 13:12
|
|||
|
Re: 115c Generator
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Why not install a newer generator and voltage regulator? The newer ones have more output. Wiring connection between the gen and VR is simple: armature is armature, field is field, and ground is ground. Physical size could be easily matched, but you may have to get a proper pulley.
(o{}o)
Posted on: 2015/5/18 13:29
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: 115c Generator
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Flackmaster,
Thank you for looking. PM sent. Thank you also convert, JW and owen for the advice/suggestions.
Posted on: 2015/5/18 13:52
|
|||
"Vision without execution is just hallucination"
|
||||
|