Re: Building a 440" Packard V8
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Will there need to be something done to the mains and webbing for the increase in displacement and HP? I was under the impression from past discussions the Packard lower end was considered somewhat weak as compared to other engines.
Posted on: 2017/2/9 17:18
|
|||
Howard
|
||||
|
Re: Building a 440" Packard V8
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Yes, photos to come of block with ARP main studs and line honed main bores.
jack vines
Posted on: 2017/2/9 17:38
|
|||
|
Re: Building a 440" Packard V8
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Maybe it's me and my laptop, but the only photo I see is the "aluminum flywheel with steel insert",
Posted on: 2017/2/9 18:01
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: Building a 440" Packard V8
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
[b]Kids, don't try this at home! It's taken many years and many dollars, but it's getting closer.
First up is finding a forged crankshaft. As most of you know, these were most likely never installed in production engines, but only available a service items after production ceased, so quite rare. Then finding an old school shop which will still build welded strokers; also quite rare. It took him three years to git 'er done, but here's a 3.875" stroke crank. jack vines
Posted on: 2017/2/9 18:36
|
|||
|
Re: Building a 440" Packard V8
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
The shop owner, who's been grinding for forty years, says the Packard forged crank counterweights aren't right. He welded on large additions to the second and fourth counterweights.
jack vines
Posted on: 2017/2/9 18:37
|
|||
|
Re: Building a 440" Packard V8
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Custom 4.25" bore forged pistons compared to OEM 374" piston.
jack vines
Posted on: 2017/2/9 18:38
|
|||
|
Re: Building a 440" Packard V8
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
And custom 7.100" rods with BBC ends.
jack vines
Posted on: 2017/2/9 18:38
|
|||
|
Re: Building a 440" Packard V8
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Quote:
Maybe it's me and my laptop, but the only photo I see is the "aluminum flywheel with steel insert", Some can see all the photos and some can't. No idea why, so I posted them individually. jack vines
Posted on: 2017/2/9 18:41
|
|||
|
Re: Building a 440" Packard V8
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Quote:
" And custom 7.100" rods with BBC ends." "BBC" meaning Big Block Chevy??? "ends" meaning Wrist pin end and rod bearing end of a Big Block Chevy???
Posted on: 2017/2/9 19:44
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|