Re: Torque specs for wheel lug nuts packard twelve
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Don't know the size lug a Twelve uses but for the immediate prewar Clipper and conventional body models plus the postwar models with 9/16-18 threads it is 85-95 ft/lbs.
Posted on: 2021/8/31 14:23
|
|||
Howard
|
||||
|
Re: Torque specs for wheel lug nuts packard twelve
|
||||
---|---|---|---|---|
Just popping in
![]() ![]() ![]() |
Thanks for the answer i did put them at 80 but it felt not tight enough, so thats why i asked.
Will put them later today at 95-100.
Posted on: 2021/8/31 17:55
|
|||
|
Re: Torque specs for wheel lug nuts packard twelve
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Be sure to check the lug diameter first as the specification provided shouldn't be exceeded for the size described. Although I am barely online and can't look it up for you, there are charts giving standard torques for many bolt diameters and thread pitches.
Posted on: 2021/8/31 17:58
|
|||
|
Re: Torque specs for wheel lug nuts packard twelve
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Just curious, and off the topic a bit (but I do believe in tight lugs), did Packard have left hand threads on the driver's side? I know that Chrysler did that. Had a '65 Dodge that was baffling me until I recalled how Mopar over-engineered/thought some things like that.
Obviously, it's been awhile since I pulled a Packard wheel.
Posted on: 2021/9/1 5:10
|
|||
If you're not having fun, maybe it's your own damned fault.
|
||||
|
Re: Torque specs for wheel lug nuts packard twelve
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
RH threads both sides.
Posted on: 2021/9/1 7:33
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: Torque specs for wheel lug nuts packard twelve
|
||||
---|---|---|---|---|
Just popping in
![]() ![]() ![]() |
The threads are all same around by Packards.
The size of my nuts are 3/4
Posted on: 2021/9/1 8:28
|
|||
|
Re: Torque specs for wheel lug nuts packard twelve
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
How many threads per inch? A 3/4" nut could be tightened considerable more that a 9/16" but it is also dependent on the pitch.
Posted on: 2021/9/1 10:44
|
|||
|
Re: Torque specs for wheel lug nuts packard twelve
|
||||
---|---|---|---|---|
Just popping in
![]() ![]() ![]() |
They are only 1.5 inch thread total. So thats looks kinda short. Will take one out and check how many windings.
Posted on: 2021/9/1 15:33
|
|||
|
Re: Torque specs for wheel lug nuts packard twelve
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
The standard measurement is in threads per inch, not how many it has it's full length. For 3/4" it would be either 10 for course threads or 16 for fine threads, unless it's something special, and I would expect a lug for a wheel would be fine thread.
The range is considerable and based on modern steel grades so for Grade 2, which is the softest, the torque would be 138 while Grade 8, which is the hardest, the torque would be 315 according to online data charts. This really doesn't answer the question as I have no idea what the steel type was or even if the grading system was used then.
Posted on: 2021/9/1 21:05
|
|||
|