|
Re: Carburetor linkage troubleshooting 6 cyl
|
||||
|---|---|---|---|---|
|
Home away from home
 
|
Which year and model?
Posted on: 1/16 13:29
|
|||
|
||||
|
Re: Carburetor linkage troubleshooting 6 cyl
|
||||
|---|---|---|---|---|
|
Forum Ambassador
 
|
Probably this one Don.
Posted on: 1/16 15:32
|
|||
|
Mal
/o[]o\ ====  Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this?  Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
||||
|
Re: Carburetor linkage troubleshooting 6 cyl
|
||||
|---|---|---|---|---|
|
Home away from home
|
Oh, the one with the screen capture. The year and model should have been in the question, I think.
Posted on: 1/16 19:05
|
|||
|
||||
|
Re: Carburetor linkage troubleshooting 6 cyl
|
||||
|---|---|---|---|---|
|
Not too shy to talk
 
|
It is a 1941 sedan
On the pictures that I have found I have seen that the carburetor throttle linkage is facing the firewall. The carburetor that I have installed on the car now the linkage is facing towards the passenger firewall I am going to upload a picture to show what I'm talking about In the picture I painted the linkage green that's coming from the gas pedal off the firewall. I put a red arrow on the carburetor the carburetor butterfly gets pushed up Attach file:  20240116_225644.jpg (6,209.16 KB) 20240116_225653.jpg (6,625.63 KB) 20240117_132446.jpg (4,102.98 KB)
Posted on: 1/17 13:28
|
|||
|
||||
|
Re: Carburetor linkage troubleshooting 6 cyl
|
||||
|---|---|---|---|---|
|
Home away from home
|
There is supposed to be a bell crank attached to the pin sticking from the manifold which transfers the front to back motion to vertical motion and another linkage connected from it to the carburetor.
As for whether it's the correct carburetor, you can look up the carburetor in the parts book which should answer that. It LOOKS like it but there were variations used on other makes and models so impossible to tell from the photo. UPDATE: I could not find a photo anywhere and Clipper is apparently different. Also different is ElectroMatic Clutch but your car does not appear to have that option. As for the bell crank and linkage, I likely have it at my shop but unfortunately it is hundreds of miles away at the moment so I can't help. Try Tucson Packards as they have several 1941 parts cars and tons of parts.
Posted on: 1/17 15:40
|
|||
|
||||
|
Re: Carburetor linkage troubleshooting 6 cyl
|
||||
|---|---|---|---|---|
|
Not too shy to talk
|
Thanks a million
I have a much better idea of what I'm looking for now. & Now I will definitely reach out to the parkard people you referred. I hope you create yourself an amazing night out of it ;)
Posted on: 1/17 19:39
|
|||
|
||||
|
Re: Carburetor linkage troubleshooting 6 cyl
|
||||
|---|---|---|---|---|
|
Not too shy to talk
|
1941 19 series 110
The engine is a 6 cylinder
Posted on: 1/20 10:18
|
|||
|
||||
|
Re: Carburetor linkage troubleshooting 6 cyl
|
||||
|---|---|---|---|---|
|
Not too shy to talk
|
I just found this picture
After I searched for bell crank It looks like mine THANK YOU Attach file:  IMG_0003.png (3,422.57 KB)
Posted on: 1/20 14:58
|
|||
|
||||
|
Re: Carburetor linkage troubleshooting 6 cyl
|
||||
|---|---|---|---|---|
|
Home away from home
|
That appears to be a RHD (right hand drive) car but same idea.
Posted on: 1/20 16:12
|
|||
|
||||
