Re: Shudder
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Assuming there is no grease on the clutch disc then in addition to checking the condition of engine and trans mounts also check and see if there is a snubber bar on your car mounted between a bracket on the trans and another to the frame. This was an item introduced in the late 30s and carried on in various forms until the 51 models.
Not all models needed them but it was added to help control what Packard called clutch chatter. The 3 point engine mounts on the models prior to 51 could allow the engine to shift slightly fore and aft and the bar was added to help control this motion. While the problem was mostly in reverse, it could also happen in low as the car started out from a stop. Check to make sure the brackets are tight and the rubber bushings at each end at the rod/bracket connection have not deteriorated. Bar was adjusted fairly snugly to add a slight bit of tension to the engine/trans assy to stabilize any fore/aft movement and keep it to a minimum. Here is a 21st series version which would be very similar if not identical to what would have been on any 22nd series models equipped with the bar. If your car does not have one perhaps something could be fabricated and tried if no other reason for the shudder is found.
Posted on: 2021/5/25 10:48
|
|||
Howard
|
||||
|
Re: Shudder
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
This is great info! I actually saw the snubber bar last night when inspecting the motor mounts. I did give it a tighten a bit only like a 1/4 turn as it seems pretty tight. I will be looking for the transmissions mounts to the frame tonight but having a hard time locating. Thanks again!!
Posted on: 2021/5/25 11:09
|
|||
|
Re: Shudder
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
The trans mounts are hard to see from below. One side of the mount is bolted toward the front of trans just behind the bellhousing on each side of the transmission. A rubber block is vulcanized between two pieces of metal and the other side mounts to the main support crossmember at an angle fairly hidden from below. The rubber blocks could be hard as a rock or even separated from the metal on one side. If yours are bad, as far as I know the only options are to have them revulcanized by Steele Rubber or maybe check with Kanter. He had mounts for some models repro'd and if yours is one of those and he still has any the price for the repro pair was less than the revulcanizing service.
The front mount is also known to deteriorate quite badly. That consists of two pieces of metal bolted together with a sandwich of rubber squeezed between them. Steele does have new rubber pairs for that one. Here is the front mount but I don't have good photos of those on the trans.
Posted on: 2021/5/25 11:46
|
|||
Howard
|
||||
|
Re: Shudder
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Again thanks for the pics and info! I will check in the condition of the mounts. According to the Shop Manual and Shop Updates changing the clutch is the last resort after checking all other options and by the sound of it I am leaning towards the mounts being old and or loose.
Posted on: 2021/5/25 12:03
|
|||
|
Re: Shudder
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
No way to know what condition your car is in, but typically clutch chatter comes form some sort of contamination of the clutch face or warping of the flywheel surface. A rear main seal leak is a typical culprit. Sometimes bearing wear is involved. You might be able to adjust it out or you might be in for more than just a clutch change. If it's not harmful, as in stalling or slipping at speed, then maybe best to leave alone depending how much you drive it and plan it for later. Probably need to put it in the air and inspect.
Posted on: 2021/5/25 19:43
|
|||
|
Re: Shudder
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
G'day Pipesargent,
![]()
Posted on: 2021/5/25 20:22
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: Shudder
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
Just uploaded my cars info into the registry.
Posted on: 2021/5/26 9:52
|
|||
|
Re: Shudder
|
||||
---|---|---|---|---|
Quite a regular
![]() ![]() ![]() |
I have to agree with you…. I just use it to go to car shows and ice cream or a short cruise not driving across country with it so I might just let sleeping dogs lie. Thanks again for the advise.
Posted on: 2021/5/26 9:54
|
|||
|
Re: Shudder
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Quote:
Pipesargent wrote: Just uploaded my cars info into the registry. ![]()
Posted on: 2021/5/26 14:33
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|