Re: Backing board for door panels. what to use?
|
||||
---|---|---|---|---|
Forum Ambassador
|
If you have a friendly local upholsterer who will order from his supply house you can buy a replacement water resistant cardboard which is pretty close to the original thickness. Ordering that way will probably avoid a large freight charge. When I first looked into the cardboard for my on/off glovebox project, freight was way more than the material. Fortunately an upholsterer friend would order it for me. If no one local, here is a mail order placeperfectfit.com/15347/154533/Chipboard-Ca ... -Treated-Waterproof-Panelboard.html Restoration Specialties also carries it.
I know some have used a 1/8" fiberboard from the home center which is close to the original in looks but not water resistant and, IIRC is just a tad thicker. Luan plywood used for door skins has also been used. I used 3/16 Masonite about 15 years ago which is much too thick -- but all I could find here at the time. No matter which you use, cutting the multitude of holes for the clips and everything else is a pain.
Posted on: 2012/3/11 22:34
|
|||
Howard
|
||||
|
Re: Backing board for door panels. what to use?
|
||||
---|---|---|---|---|
Home away from home
|
Good info! Cutting holes can be accomplished with different sized brass or copper tubing, sharpened to a bevel on one end. Pakardtaximan suggested picking up a cheap socket set and sharpening the ones you need to punch holes with. Of course, this only works for round holes.
Posted on: 2012/3/12 7:56
|
|||
Joey
(?=#=?) "If chrome got me home, I'd for sure still be stuck somewhere." [url=http://pac |
||||
|
Re: Backing board for door panels. what to use?
|
||||
---|---|---|---|---|
Home away from home
|
Thanks Howard! Thanks Joey!
Posted on: 2012/3/12 9:00
|
|||
|
Re: Backing board for door panels. what to use?
|
||||
---|---|---|---|---|
Home away from home
|
You can buy inexpensive hole punch sets at Harbor Freight or Northern Tool.
(o[]o)
Posted on: 2012/3/12 11:02
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: Backing board for door panels. what to use?
|
||||
---|---|---|---|---|
Home away from home
|
We used to use a product called Sentra Board, a plastic available from art supply places. Comes in sheets of various colors and thicknesses.....
Here is one sourcesintrapvc.com/
Posted on: 2012/3/12 15:37
|
|||
When two men ride the same horse, one has to be in the back...
|
||||
|
Re: Backing board for door panels. what to use?
|
||||
---|---|---|---|---|
Home away from home
|
Just made a driver's door panel for my 56 this evening. Used 1/8 tempered masonite as it is cheap and readily available.
I bolted the stripped old panel to the new masonite with 4 bolts and washers so it could not shift. It was then an easy matter to cut along the edge of the old panel with a fine blade in the jigsaw to make the new one the exact size. All the pertinent new holes were drilled right through the old ones for perfect location. I did the retainer clip holes by drilling 5/16 at each end of the rectangle and then squaring up the hole with the jigsaw. After unbolting, I hit all the ragged edges with a sanding disk and beveled the edges of the panel so the material will wrap nicely. After the new panel is assembled, will paint the back with polyurethane. Total time to make the panel came to 45 minutes including getting the tools out. I'll put them back tomorrow 'cause it was suppertime!
Posted on: 2012/3/12 19:20
|
|||
|
Re: Backing board for door panels. what to use?
|
||||
---|---|---|---|---|
Home away from home
|
Thin Masonite is the closest and best material you can use for backing on V-8 door panels.
Posted on: 2012/3/14 21:10
|
|||
|
Re: Backing board for door panels. what to use?
|
||||
---|---|---|---|---|
Home away from home
|
Thanks Guys! I now have new options to explore. One more great aspect of this website!
Posted on: 2012/3/14 21:47
|
|||
|
Re: Backing board for door panels. what to use?
|
||||
---|---|---|---|---|
Not too shy to talk
|
Another choice is picture matting board. I have used that in the past, after skim coating each side with epoxy resin (not polyester resin). Good thickness, workability, durability, can laminate using epoxy to exactly match thickness. You can even complete all your access holes, and then do the epoxy thing, so that the edges of the holes are treated to prevent fraying or moisture intrusion. Trick came from my other hobby, boat building. Can easily get matting from art supply store chain like "Michael's". MCB
Posted on: 2012/3/15 8:32
|
|||
|