Packard Forum Index » Project Blogs

Tuesday 7th September 2010

Not at the workshop today, although I did drop in to look for my mobile phone which I lost misplaced yesterday. Found it wedged between the base of the front seat back and the seat squab of Old Blue. Pheeew! Then it was off to rendezvous at McDonald's at Thornleigh for the OASIS run to Mooney Mooney today. Wade and Gina were going in Big Red while I was giving the '41 a hit out. Unfortunately I couldn't stay for lunch, because of babysitting commitments, but more than 40 people did so at the Mooney Mooney Workers Club. However the run up the Pacific Highway heading north and on the Freeway on the southerly return trip did give a perfect opportunity to test the OD. And the kick down worked well once I got the hang of it. Initially I was just stabbing the pedal to the floor momentarily but it didn't kick down. But flooring the pedal and holding it there for a second or two did the trick and kick down was obtained. In this age of instant gratification we come to expect things to happen now! We need to be reminded from time to time that it wasn't always so. Won't see Wade until Thursday because tomorrow, Wade and Gina are heading south to pick up some more finished body parts for the '34.

Link to the pic's taken today. As you will see I was quite taken with the Austin 12 with the divider window. Didn't know Limo's came in such small packages. OASIS run to Mooney Mooney

Attach file:

---

  (52.02 KB)


  (47.92 KB)


  (55.58 KB)

Wednesday 8th September 2010

No workshop today, with Wade and Gina heading south to pick up '34 parts.

Instead, had my Packard fix when our granddaughters came over to play. And how did I get a Packard fix in that sort of circumstance? By playing in, around, over and on the '41! The little girls are 2yo and just turned 4yo. The 4yo wanted to play in Poppy's car, meaning the '41, and the 2yo tagged along. With them both in the front seat the 4yo bipped, or should I say blasted, the horn and then bipped/blasted again and again. The noise was too much for the 2yo being soon in tears and happy to vacate the '41's front seat. This left Poppy and a very energetic 4yo, tugging on the steering wheel, shifting the gear lever, rolling windows up and down, opening and closing quarter vent windows and opening a door, climbing out, shutting the door, opening the door, climbing back in, shutting the door, etc, etc. All I had to do was sit back, enjoy the experience and comment about how wonderful and clever she is, and she is! Till at one point, in the door opening and closing routine, the door closed and remained closed. Then I saw a little blondish head emerge in front of the windscreen hauling herself up the front mudguard(fender) and pull herself up onto the bonnet(hood). She even stood up on the mudguard but was soon dissuaded from that activity. Talk about enjoying a Packard! She certainly was, using it as a plaything and Poppy couldn't have been happier. For her weight and wearing soft soled shoes she posed no threat to the bodywork and I was more than happy to let her do this. Also remember my '41 is a driver at best and to gain another use for it and at the same time giving my granddaughter fun was quite acceptable from my viewpoint. After a number of ups and downs onto the mudguard and bonnet, interspersed with a photo shoot, she then discovered the '41's front mudguard made a great slippery dip as a means of returning to the garage floor, even more fun! That then became part of the routine. Could have spent all day doing this and loving every minute of it.

Back to the workshop tomorrow and, even though I'll be working on Packards, it sure won't be as much fun as today was.

Attach file:

---

  (26.82 KB)


  (31.81 KB)


  (36.77 KB)


  (39.63 KB)


  (31.44 KB)


  (34.00 KB)


  (22.38 KB)


  (26.02 KB)


  (34.09 KB)

Mal, nothing like having a "little" help. Priceless. We are so lucky.

(o{I}o)

Attach file:

---

  (50.33 KB)

Thursday 9th September 2010

Quote:John, you're so right.

Quote:Terry, I didn't lie, it's just that I need to polish the crystal ball!

Actually worked on the '34 today. The '39 expected for a pre National Rally tune-up, service and check-up hasn't arrived yet because it's waiting for bodywork to be completed. So in it's absence the '34 finally came to the head of the queue. While yesterday Wade and Gina headed south and picked up some more '34 parts from the painter. All that remains to be painted and picked up are the front 'guards(fenders-US, wings-UK) and the bonnet(hood) side panels.

Amongst the painted panels picked up yesterday was the radiator shell. So we set about installing it on the '34. Turned out to be a tight squeeze to get it onto the radiator and radiator shutters set-up on the chassis. It was also complicated a bit by the fact that when Wade bought the '34 some 10 years or so ago it was in pieces and so Wade in putting it back together didn't have the benefit of the taking it apart phase. The front of the '34 features a very strong structure tying together the mudguard(fender) brackets and headlight mounts by means of a bar between the radiator and shutters which has a large flange at each end. Until this bar and it's associated flanges is in position it creates some difficulties in aligning the radiator shell so that it fits past the shutters, up and over and down on the radiator filler neck, under the bottom of the chromed shutter base and the tabs on the vertical centre divider bar aligning with their slots. But in the end it all went together. A nice finishing touch was the mounting of the crank hole escutcheon, looks good!

During this exercise Harvey arrived bringing with him a rebuilt cowl vent drain tube. This tube is steel tubing, with a 'Y' junction at top, which runs down inside the firewalls exiting behind the engine block at the base of the outer firewall. The tube Wade had was very rusted around the 'Y' junction and some months ago Wade had started bending up a replacement using copper tubing. But because it has an out, and then an in bend, near its base getting bends without kinks like the original was proving impossible to do. Last week when Harvey was over he'd volunteered to do it in steel tube and had phoned Wade on Monday saying it was ready. Harvey found that bending the in and out bottom bends was also an impossibility but came up with an innovative solution. Use the bottom off the original tubing complete with bends and mate a new top section to it with the appropriate 'Y' junction. Worked out well.

Next we turned to the firewalls. Yes, that's right, its plural with an inner(passenger cabin side) and an outer(engine side) firewall. Maybe the inner is a bulkhead, rather than a firewall? Anyway between the two is a double layer of sound deadening/heat insulating caneite material. This was being replaced because although Wade has one, from the '34 he bought to replace the body destroyed by fire, it's LHD and his is RHD. The inner firewall(bulkhead?) is from the LHD car but it's been modified to now be RHD to suit the fully restored chassis. The only body panel salvaged from the fire is the engine side firewall, Wade wants to retain the <Thief Proof> number of his original '34. Sorry O_D! Some months ago I'd cut out the caneite but hadn't finished marking and cutting or drilling all the holes, cut-outs and recesses required. It was complicated by the fact of using the two different inner and outer firewall panels which had some holes/fitting points which weren't required. So with a lot of comparing, between inner firewall/bulkhead, outer firewall, US caneite and US outer firewall, the new caneite panel was sculpted with holes and cut-outs. At the end of the day it goes together well, but hasn't yet been mounted permanently to the body.

Attach file:

---

  (19.56 KB)


  (18.39 KB)


  (42.69 KB)


  (29.98 KB)


  (32.64 KB)


  (22.15 KB)


  (38.10 KB)


  (24.11 KB)


  (30.70 KB)


  (32.63 KB)


  (24.70 KB)


  (35.80 KB)

I have heard that filling the tube with sand will help keep the copper tube from kinking as you bend it.

Quote:

Yup, that's how organ builders made pipe organs back in the day.

my friend did this all the time when he had no pipe bender, he filled with sand and it worked great!

Hank

Many years ago a mate of mine, not having a pipe bender or access to one, used the sand filling method when bending up exhaust pipes for the hot rods and dragsters he built, sometimes successfully sometimes not. I don't know how well this would translate to the small diameter tubing used here, about 3/8". Part of the success factor involved was filling the tubing by packing the sand in then plugging each end to prevent any sand egress during the bending process. Not sure how you would plug the small diameter tubing being used in this application. Anyways, in this instance, being able to retain part of the original tubing and just replace the badly rusted Y piece has resulted in a great outcome.

Hello, on my 37 115C the sending unit is connected to block with a square nut , my question is how is this removed? is it turned as a threaded nut ? I want to make sure as not to damage it. Thanks, Richard

Quote:Richard,

I'm not sure what you're referring to here but I suspect it's either the oil pressure, most likely, or temperature gauges sending/mounting points. Can you be more specific please, or post a pic of what you have?