Re: V8 pilot bearing
|
||||
---|---|---|---|---|
Home away from home
|
The most recent T85 input I measured via a Starrett micrometer is .588".
jack vines
Posted on: 2015/1/29 8:57
|
|||
|
Re: V8 pilot bearing
|
||||
---|---|---|---|---|
Home away from home
|
If there is some controversy about pilot bearing dimensions then it is probably due to transmission variations whether production or otherwise.
I've ran into problems over the years where there were variations in input spline shafts, pilot bearing differences as well trans case length differences. Especialy among mongral car companies such as AMC, Opel and others. 65/66 Rambler classics were for all intents and purpose the same car. However the 66 3spd manual trans case was about 5/16" shorter than the 65. Different splines on input shaft. Maybe a few other small but inportant variiations. OTherwise, on even a close visual inspection the 65 and 66 trans looked identicle.
Posted on: 2015/1/29 9:18
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: V8 pilot bearing
|
||||
---|---|---|---|---|
Home away from home
|
Nice. After you have installed it and find the added thickness does not pose a problem it should be added to the parts interchange.
Posted on: 2015/2/2 9:04
|
|||
|
Re: V8 pilot bearing
|
||||
---|---|---|---|---|
Home away from home
|
I just ordered one off feebay, for less than $10, with shipping. I looked at two crankshafts yesterday, and the pilot bearing recess is at least an inch deep, so I seriously doubt the extra 1-MM (3/64") width of this bearing will be a problem. Also, if the bearing will hold up in an alternator, I am sure it will do just fine as a pilot bearing. Will find out, and report back.
Posted on: 2015/2/2 14:56
|
|||
|
Re: V8 pilot bearing
|
||||
---|---|---|---|---|
Home away from home
|
I have the bearing in hand, and it looks like a perfect fit.
Posted on: 2015/2/14 12:57
|
|||
|
Re: V8 pilot bearing
|
||||
---|---|---|---|---|
Home away from home
|
better mic it. especialy the o.d. .
Posted on: 2015/2/14 15:19
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: V8 pilot bearing
|
||||
---|---|---|---|---|
Home away from home
|
I can't believe this thread is still going.
Joe H definitely gets a cold Barley Pop for his detective work. Joe, are ya'll working on a stick car?
Posted on: 2015/2/14 15:38
|
|||
|
Re: V8 pilot bearing
|
||||
---|---|---|---|---|
Just popping in
|
This part number is listed correctly in Studebaker parts listing and I have ordered one from Brent Hagen and it is the right bearing..47mm/15mm/14mm..421731
Posted on: 2017/4/13 9:25
|
|||
|
Re: V8 pilot bearing
|
||||
---|---|---|---|---|
Forum Ambassador
|
G'day mrumfelt,
Although a long time member here, first post, so to PackardInfo. And......I invite you to include your V8(?) Packard in the Packard Owner's Registry.
Posted on: 2017/4/13 18:22
|
|||
Mal
/o[]o\ ==== Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|