Re: Straight Eight engine number/cid
|
||||
---|---|---|---|---|
Forum Ambassador
|
Here is the engine number reference Kev madepackardinfo.com/xoops/html/downloads/PackardEngineSerials.pdf H225423 is in the 49 half of 23rd series, a 288 used in a standard or deluxe 8.
EDIT: 3 replies with the info in 5 minutes time. Not bad.
Posted on: 2011/7/31 16:28
|
|||
Howard
|
||||
|
Re: Straight Eight engine number/cid
|
||||
---|---|---|---|---|
Home away from home
|
Guy, I delved into an old thread that sounds like thunder. Perhaps you should at least give it a cursory glance?
Posted on: 2011/8/5 18:47
|
|||
The story of ZIS-110, ZIS-115, ZIL-111 & Chaika GAZ-13 on www.guscha.de
|
||||
|
Re: Straight Eight engine number/cid
|
||||
---|---|---|---|---|
Home away from home
|
Thanks, Guscha. Good info on the various options for achieving different compression ratios on the 288 and 327 engines. I read it all with interest.
The 288 in question is a plain vanilla '49 "STD" with 7:1 compression ratio. I'm not too interested in modifications, but in how the engine would perform in its present state, assuming t is in good operating condition. F'r instance: -What is the potential for highway cruising speeds of 70 mph with this engine. -What rear end ratio would be needed to achieve these speeds without over-revving, given a standard transmission and no overdrive. -How reliable and durable is this engine to run, (given today's alcoholic gas). -How efficient is it mileage-wise. -What are the typical "major malfunctions" to expect needing attention. -What are the strong points of the engine? Thanks very much.
Posted on: 2011/8/7 12:56
|
|||
Guy
[b]Not an Expert[/ |
||||
|
Re: Straight Eight engine number/cid
|
||||
---|---|---|---|---|
Home away from home
|
with my 50 288 and ultramatic i did 70mph no problem, regularly. highway was about 80% of my driving.
Engine ran reliably, had no carb or fuel pump issues, put about 3000-6000 miles on that motor on today's gas. I believe the 288 wasn't the problem with overreving as much as the 327, perhaps others more knowledgeable could chime in?
Posted on: 2011/8/7 16:23
|
|||
|
Re: Straight Eight engine number/cid
|
||||
---|---|---|---|---|
Home away from home
|
Back in those days Road and Track Magazine regularly remarked that 2500 feet per minute was a good guideline for maximum reliable/sustainable piston speed. On a 327 that would equal 3529 rpm, and on a 288 an even 4000 rpm. With the 3.9 axle usually specified with straight stick that would yield 75 and 85 mph respectively.
And sure, they will do that, but they sure do sound busy when pushed that hard. Early fifties Ultramatic cars often were fitted with 3.54 axles which pushes them up to 83mph for a 327 and 94mph for the 288 without excessive piston speed. That's close to how fast a 288 is going to push one of those barn doors through the wind in any event. As a contrast, an overdrive car is only turning 2100 rpm at 70 and feels quite relaxed. Its maximum safe speed (with 288)if Road and Track's number is followed is 118 mph--something it can only achieve over the side of a cliff. Mine is very happy at 80 but sucks up fuel like a fighter jet when driven that fast.
Posted on: 2011/8/7 18:48
|
|||
|
Re: Straight Eight engine number/cid
|
||||
---|---|---|---|---|
Home away from home
|
Quote:
Back in those days Road and Track Magazine regularly remarked that 2500 feet per minute was a good guideline for maximum reliable/sustainable piston speed... Ross, thanks for your always cogent comments. One cannot overemphasize the importance of "Back in those days". The maximum piston speed of modern-day cars are remarkable higher, approx. 3.500 up to 4.000 feet per minute (~ 20 m/s) because of other materials and technologies (X-rayed aluminium pistons, low-viscosity engine oil, ...) and even in old days the piston speed of high-performance engines could be much more increased. MZ RE 125; made in GDR in 1965, single-cylinder two-stroke engine, oval-shaped aluminium alloy piston, maxium piston speed 4.724 feet per minute (~ 24 m/s) [picture source:cyclechaos.com/wiki/MZ]
Posted on: 2011/8/8 5:55
|
|||
The story of ZIS-110, ZIS-115, ZIL-111 & Chaika GAZ-13 on www.guscha.de
|
||||
|
Re: Straight Eight engine number/cid
|
||||
---|---|---|---|---|
Home away from home
|
Sustained 3500 - 4000 rpm on the long stroke streight 8's mite very well be just fine . But how many miles between engine overhauls?????
Posted on: 2011/8/8 7:21
|
|||
VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245 |
||||
|
Re: Straight Eight engine number/cid
|
||||
---|---|---|---|---|
Home away from home
|
My experience is that pieces of top piston ring will be popping up through the top of the piston on their way to a rendezvous with the exhaust valve, especially if the car has over 80k miles or so, and was equipped with the bird-strainer air filter so many of those cars were afflicted with.
With top rings that actually fit grooves that aren't noodled out they would probably run a long time at those speeds. I don't have the slightest fear for the bottom end or the valve train. Let me quote from my all time favorite Service Counselor, talking about how to solve a vibration problem in 200s with Ultramatic (April 1951): "The disturbance, when it exists, is particularly noticeable between 80 and 90 miles per hour. In some instances, a disturbance may also be noticeable at speeds below 80 miles per hour". And that is why I like Packards.
Posted on: 2011/8/8 9:51
|
|||
|
Re: Straight Eight engine number/cid
|
||||
---|---|---|---|---|
Home away from home
|
I put a self imposed RPM cruise limit on my 38 (282 engine) of 2500. That coupled with the stock 4:36 rear end and an R11 overdrive gives me 66 MPH. I found that anything above that speed the car is not overly relaxing to drive. I took my measurements with a GPS and a tach
Posted on: 2011/8/8 12:06
|
|||
1938 1601 Club Coupe
|
||||
|