Re: BigKev's 1937 115-C Convertible Coupe
|
||||
---|---|---|---|---|
Webmaster
|
Gerry at Packards Southwest had one of these hard to find items and it's on the way to me!
Thanks Gerry! Quote:
Posted on: 4/13 16:16
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Re: BigKev's 1937 115-C Convertible Coupe
|
||||
---|---|---|---|---|
Webmaster
|
Begone foul breast!
I exercised the old fuel line and pump from the car. It was a conglomerate of a little bit of copper hard line and mostly rubber rubber all far on the inside of the framerail. The fuel pump was mounted mid-ship between the muffler and the framerail. Not it's all brand new hardline front to back except for a 12" piece of fuel hose between the framerail bulkhead fitting and the fuelrail for the carbs. And a couple of small 4" pieces where the fuel pump was plumbed inline back my the tank. The line is now ran exactly in the same routing that the factory line would have been. Down the outside of the framerail and using the clips along the runningboard supports and rail where needed. Now sure it it's just me, but it appears to run better after doing that.
Posted on: 4/13 17:14
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Re: BigKev's 1937 115-C Convertible Coupe
|
||||
---|---|---|---|---|
Home away from home
|
Probably does, the fuel would flow smoother/easier and get to the motor cooler too. Well done!
Posted on: 4/13 17:30
|
|||
|
Re: BigKev's 1937 115-C Convertible Coupe
|
||||
---|---|---|---|---|
Webmaster
|
Got a few things done this evening.
First I installed a "Hope I never need it" accessory. The bracket is attached to the floor. Next since I've had the car it's had a few mystery leaks. Leaking coolant from the engine towards the back. I re torqued down all the head nuts. There actually were a few that were a couple of pounds shy of spec. The jag motor has an external water distribution tube and I think part of the leak maybe where it bolts to the engine. So I tightened down all those bolts as well. That all helped, but still had a seap in a few spots. So next up was the pulp pellets. Basically one pellet takes care of 1/2 gallon of coolant capacity. So I needed 8 pellets as the coolant system takes about 4 gallons. So after pre-crushing the pellets and mixing them up with a little bit of new coolant in a mixing cup, I got engine up to temp so I knew the thermostat was open and circulating and poured the slurry into the radiator and let circulate for 15 mins. I then prepared to paper train the Jackard to identify locations of any additional leaks. Fresh Newspaper on a clean drip tray, and a couple of magnets to prevent the paper from moving around. And under the car it goes. I'll check in the morning and see if there is any evidence of coolant. I know am seaping a little bit of oil. Which I think is one of cam oil lines in the rear. Also maybe a bit of rear seal leak.
Posted on: 5/7 19:53
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Re: BigKev's 1937 115-C Convertible Coupe
|
||||
---|---|---|---|---|
Home away from home
|
Quote:
I may have chuckled at this typo!!
Posted on: 5/8 15:08
|
|||
|
Re: BigKev's 1937 115-C Convertible Coupe
|
||||
---|---|---|---|---|
Webmaster
|
Quote:
No, trust me, it involved some exercise!
Posted on: 5/8 15:10
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|