Packard Forum Index » Project Blogs

Wednesday 11th January 2012

Yesterday I said: "....Wade needed to do his parts run ....to drop off Juniors engine, drop off the 426 waterpumps and...." but today I noticed all the waterpump parts were still on the bench so obviously they didn't go yesterday. Also learned today that the machining, fitting and balancing work on Junior's engine is expected to take about three weeks to do. First up today was greasing the Coupe, much easier doing it up on the hoist rather than lying on your back under the car. I also asked Wade about the front wheels, which seemed to have a bit of give and take in them when rocked from side to side and in and out up on the hoist. Prognosis was the wheel bearings needed tightening, after which I adjusted all the brakes. Next the Coupe was lowered to the floor and the drivers side bonnet(hood) catch was repaired because it failed to open yesterday when I arrived at the workshop, just needed a washer. Why there wasn't a washer there before, I don't know. Next was repairing the OD lockout knob. I'd bought a new one but, in my heavy handed manner, managed to pull the knob off its metal insert. A little super glue and knob and insert were re-united, hopefully never to come apart again.

While I was greasing and adjusting Wade was also busying himself preparing Juniors transmission for when it's re-united with the rebuilt engine. Wade, as you know, has a great aversion to leaks which Juniors trans and OD have in spades. Amongst the parts bought in was a trans and OD gasket kit(What! MBM isn't good enough now?) together with new seals for the trans top selectors. First thing Wade found in cleaning up the trans top for the selector arm shaft seal replacement was that the top over one of the seals had been flattened resulting in a crack in the cover. Pointless to put a new seal in with a crack like that so the trans/OD unit which has contributed many parts since being donated by a PACA member about three years ago again came to the rescue. One of the selector arms from the donor trans/OD was also utilised in preference to Juniors. New seals in the the trans top, selector arms sorted, top retaining bolts and washers and the vent cap cleaned up then turned to the next task. Pulling the trans and OD apart for cleaning, reassembling with new gaskets and painting. All went well until we came to P/N 338514 the Pinion Cage Assembly in the OD. This one was a little different to the others previously worked on, or so we thought. On this one the hub for the Pinion Cage Assembly was separate to the body. Plus we couldn't get the hub off! It should just slide off without any effort. This one didn't want to budge at all! Use of levers, pullers, drifts all failed to budge it. Also used the hot spanner with the hub heated to red hot in conjunction with a heavy duty puller and a rattle gun, still wouldn't budge! Called for drastic action by employing an angle grinder to cut through the hub along the path of one of the teeth into the shaft. This action necessitated the body of the Pinion Cage Assembly being sacrificed, because it was in the cutting wheel's path. Not to worry though, the donor trans/OD appeared to have a reasonable one. Even with a slot cut almost through the collar, then employing cold chisels as wedges failed to gain any movement in the collar. By this time Rick, John and Graham were gathered around lending advice, tools and muscle but even all that failed. Next was cutting another slot about 180 degrees from the first one. Then Rick wielding a BIG hammer on a large but blunt cold chisel of his, using that as a drift gained some movement on first one piece of collar then the other. Finally with both pieces of the collar off it was apparent what the cause of the removal problem was - twisted splines on the end of the trans main shaft!!! With the collar off and the remainder of the Pinion Cage Assembly off it was apparent that the collar had separated from the body of the Pinion Cage Assembly. Further disassembly also found a broken governor pawl, I think that's what it is. Now all this is in all likelihood connected with the broken uni-joint and rotating diff housing suffered by Junior last year. But, although a static test was performed in running Junior up on the hoist and engaging and disengaging OD, there hadn't been a real road test and consequently no load on the OD so would have remained undiscovered until on the road again with the rebuilt engine. Carried on then disassmbling the remainder of the OD as well as the trans. Plan now is to use the Juniors trans case, the donor case has potential leaks from too long bolts being used on the trans mounts which have pierced the trans body, and the internals from the donor case although if worst comes to worst there could be some mixing and matching, all depends on what's found on closer examination.

Attach file:

---

  (30.07 KB)


  (41.84 KB)


  (39.21 KB)


  (32.66 KB)


  (45.43 KB)


  (43.80 KB)


  (34.97 KB)


  (35.54 KB)


  (39.15 KB)


  (41.15 KB)


  (43.34 KB)


  (42.62 KB)


  (47.13 KB)


  (38.80 KB)


  (40.48 KB)


  (24.58 KB)

Thursday 12th January 2012

After a long morning spent playing with the grand-daughters, even better than playing with Packards in my opinion, arrived at the workshop to find Wade had spent his morning cleaning all the parts disassembled from Juniors trans and OD yesterday. Meant a pre-clean to remove the vast majority of dirt, oil, grease and grime before the parts that could, went into the parts washer for a sparkling finish. Wade had also called John, Juniors Dad, last night and suggested he call in today to see the damage and discuss plans and options. This John did, but unfortunately I missed his visit because of "family commitments". Wade did say that John said he'd like to find a pair of horns for Junior. Junior at present has one long trumpet type horn mounted on a home made bracket affixed to one of the radiator to body brace rods. Wade said he had a pair of horns on the shelf which although also not kosher are more in keeping with what Junior should have. Gave them a brief bench test, they work, but need some work and to be tuned.

When I arrived Wade was just about to start disassembling the donor trans and the remaining parts of the OD. Came apart much easier than Juniors, the only "problems" being finicky or awkward circlips which necessitated a number of attempts to release and remove them. Apart from that everything slid off or out without any problems. But.....the mainshaft proved to be a disappointment, with the case hardening worn through on the second gear synchro surface, I think that's what is was. Please be gentle with me if it isn't. This led to Wade attempting to press off the corresponding part from Juniors main shaft but without success. Wade had to try even though he knew the mainshaft comes as an "assembly" and theoretically, right Randy, can't be separated. Of course he got nowhere but he did try. Fortunately John had given instructions to do what is reasonably necessary to return Junior to prime operating condition, not irrespective of cost but bearing cost in mind. So it looks like Wade's favourite Packard parts supplier will be receiving a query re availability and cost of a mainshaft and some other trans and OD parts. Although one part we looked at in the shop copy of the catalog is listed as "enquire". Does this mean you'll be lucky or you'll be very lucky and if you are be prepared for significant sticker shock?

Attach file:

---

  (44.15 KB)


  (22.34 KB)


  (22.93 KB)


  (33.02 KB)


  (53.96 KB)


  (16.83 KB)


  (42.77 KB)


  (45.23 KB)

Friday 13th January 2012

Besides giving plasma at the Blood Bank this morning learned that as well as today there are 2 more Friday the 13th's this year. Meanwhile at the workshop the elves, although I thought Christmas was over, had been at work. Or was that just one elf by the name of Wade? Whoever it was, they'd repaired a leaking oil pressure gauge fitting at the rear of the block by removing it, cleaning it and re-installing it using thread sealing tape. No more leak there now. Come to think of it Wade does have an aversion to leaks so the finger is turning in his direction. Apparently it also looks like there is a slight coolant leak from the front of the engine but neither under car or on top close inspection could pinpoint the source. Will keep a close eye on that situation in future. Then took the Coupe out for a test drive as well as filling up with 95 Unleaded and returning via George's workshop. George was able to inspect and test the Coupe for it's annual inspection certificate. The inspection approval is now done on-line so I was able, on returning home, to log on and make the required payment. The Coupe is now officially "on the road" for another year.

Wade had earlier taken Juniors mainshaft around to Brookers Brake Service so the fitting at the front(see pic) cab be machined off in their lathe. Reason being, Wade had been in contact with his "favourite Packards Parts supplier" but a combination of sticker shock and other factors has led to other alternatives being examined before any order is placed. Left Wade completing the "engineering drawings" for the machining required on the 426 waterpumps.

Attach file:

---

  (26.56 KB)


  (23.97 KB)


  (16.15 KB)


  (17.63 KB)


  (30.82 KB)

Mal,

The 'bumps' on the springs are slippery bits Packard put on their springs to eliminate squeaks. I would say that you have one OEM and one replacement spring.

I can't remember right now what material was used for the slippery bits. Maybe lead? Or rubber?

Tom

The composition of the "buttons" differed depending on position to give the optimum frictional properties and hence ride quality. Antimony/tin/lead alloys, bronze, & rubber were all used. I think the attachment, a page from an article I authored for The Packard Cormorant some years back, will give some insight.

Attach file:

---

  (126.82 KB)

Gents for the explanation and insights, my Packard education continues......

Mal, there you will find a similar question followed by explanation especially related to a 1941 110 Business Coupe.

Quote:

Dave, is one of the mentioned separator materials or a compound of it called "silenite"?

Attach file:

---

  (98.63 KB)

Selenite is a crystalline form of gypsum (calcium sulfate) as I recall. Silenite is perhaps a trade name for some proprietary substance.

I am interested to learn of what you and Wade find of this pressed swaged collar in the main shaft. A friend in Texas used an NOS main shaft assembly that ended up reciently having an issue where the collar moved allowing second and high to both engage the sliding shifter clutch resulting in shelling second gear freewheeler on the main shaft.

My transmission clearly had second gear freewheeler on the main shaft replaced as well as the input shaft. This was not evident or clear at first because I took a quick look at the input and freewheelers, and cluster which all looked good. Latter I looked at the sliding shift collar and first reverse slider discovering they were destroyed. Puzzled I looked very close at things and found the second freewheeler to be literally brand new. I noticed first / second freewheelers were loose on the bearings/ main shaft and pressed the collar back further. This took up the sloop and the gears ran perfect. I figured staking the collar would ensure it was tight and did so. It actually moved again and loosened. This was very alarming because I feared it slipping (and rightfully so as I learned almost immediately latter about the one that did in Texas) and the freewheelers moving. I ground a groove in four of the splines and TIG welded a tiny bead of weld in each to hold the collar in place.

My guess is the main shaft could have a groove machined into it and a circlip used to retain the freewheelers. If needed, I suppose the gear stack could be shimmed to get the correct bearing clearances.

I apologize for not sharing this info in my post on the '40 work progress, but figured no one would get that far into something like this and would just think I was some weird mad scientist mechanic.

Jim

Very interesting Jim, a friend in Texas recently suggested "....Repair of mainshafts may be a subject of conversation with Peter Toet as well as Jim (39Super8), who just repaired 2nd gear on his - as well as repairing hardening issues....". I'll certainly pass on what is found when the mainshaft comes back from it's machining.