Packard Forum Index » Shows and Events

Less than 200 days...

im only about 100 mi from Hershey, virus case getting worse here in Pa. i dont know if they will cancel it again or not i guess time will tell
joe

I will be at FALL CARLISLE & FALL HERSHEY and will be shopping for the following parts:

Mailing Address: John L. Trotter, PO Box 271, Kingston, TN, 37763
Email: johnltrotter@bellsouth.net Phone: 865.686.2001

1930 - 733 conv. coupe:

1. Door molding - UPPER sill/door pull molding / garnish. This the sheet metal trim piece where you would rest your arm if the window was open
2. Conv top pin - at top of windshield header
3. Door lock - passenger exterior
4. Oil level gauge – in oil pan (same 1929-1932)

1931 - 833 2-4 hardtop coupe:

1. Rumble seat step – lower one that goes inside the bumper (side mount car)
2. Visionall - windshield wiper tube and control valve. I believe the tube should measure 45.5" in length, not including the mounting brackets on the ends
3. Interior sun visor 'arms' – both sides (same as 1932)
4. Steering wheel, horn button, and surround - (any or all 3 pieces)
5. Tail light lens – red, center, hourglass shaped

1932 - 902 2-4 hardtop coupe:

1. Right rear fender – Coupe or Victoria fender (sedan fenders are different)
2. Rumble seat step – lower one that goes inside the bumper (side mount car)
3. Steering wheel, button, and surround - (any or all 3 pieces)
4. Battery box and Tool box complete with both tops and locks
5. Oil level gauge – in oil pan (same 1929-1932)
6. Running board splashers, both sides - these are the vertical sheet metal panels between the bottom of body and top of running board (same on all 902 chassis cars)
7. Air Cleaner complete with elbow
8. Gas cap
9. Frame end caps (chrome) – need 2 pairs (4 pieces)

1932 - 902 roadster:

1. Complete convertible top frame/hinge/bows entire assembly
2. Running board splashers, both sides - these are the vertical sheet metal panels between the bottom of body and top of running board (same on all 902 chassis cars)
3. Air Cleaner complete with elbow
4. Front Frame Covers – sheet metal 65.5” strips covering frame between hood/front fenders
5. Windshield post mouldings – these are the body color castings that are bolted to the vertical posts

1. My spaces are GAF 20-24, adjacent to the Packard Club tent.

2. I share these spaces with several other Packard Guys.

3. Big Kev has been known to be sighted at this location.

4. Special note to John Trotter - I don't have anything on your list, however, I will have Chris Recker with me and we can resolve your interest in a 54 Caribbean in person. I sense your frustration loud and clear.

5. I will have some parts with me to sell. If you want anything in particular, you are welcome to ask, I have the pile otherwise ready to load.

6. Safe travels to all, see you there.

David,

And all attending Hershey, I envy you, wish I could be there.

Flackmaster,

Do you happen to still have frame to crankcase splasher assembly for a 1937 One Twenty sedan? If so, I could use the passenger side (316021). I could also use two rear ash trays (housing and inserts) for the same car.

Thanks

Less than a week...the gravitational fields wax stronger daily...

Yesterday's countdown clock for Hershey.

Attach file:

---

  20210928_095142.jpg (193.39 KB)

just loaded the 37-120 engine pans onto the truck. leaving in 15 min...
GAF 20-24, my cell 214 five forty nine, tewelve fifty

Not happy colin