Packard Forum Index » V-8 (1955-56)

Topic: Frozen piston

Bottom

Previous Topic

Next Topic Register To Post

« 1 2 (3) 4 »

Craig Hendrickson

Re: Frozen piston

#21

Home away from home

Quote:

So what kind of readily available CURRENT/recent PRODUCTION over the local discount parts store counter pistons from some other engine will fit the 320 with minimal rework to the piston?????

Probably none because of the pin height. I recall going through this before on the 352 & 374.

Craig

Posted on: 2010/9/14 9:45

Nuke them from orbit, it's the only way to be sure! Ellen Ripley "Aliens"
Time flies like an arrow. Frui

Craig Hendrickson

Re: Frozen piston

#22

Home away from home

Quote:

It is a 4" piston.

What is the number on the top front of the block in front of the oil fill tube?

Craig

Posted on: 2010/9/14 9:50

Nuke them from orbit, it's the only way to be sure! Ellen Ripley "Aliens"
Time flies like an arrow. Frui

jreeder41

Re: Frozen piston

#23

Home away from home

I will check on that. I remember when I bought the car I researched the numbers and it was a 352.

Posted on: 2010/9/14 10:06

http://www.metropolitan-restoration-service.com/

Stay classy!

jreeder41

Re: Frozen piston

#24

Home away from home

The block number is 5567.

Each of the pistons have handwritten on the boss above the wrist pin 3572. Where the pistons made in matched sets or is this something that may have been done after the factory?

Posted on: 2010/9/14 10:33

http://www.metropolitan-restoration-service.com/

Stay classy!

Cli55er

Re: Frozen piston

#25

Forum Ambassador

its a 352 then.

Posted on: 2010/9/14 11:00

1937 Packard 138-CD Deluxe Touring Limousine
Maroon/Black 1090-1021
[url=https://packardinfo.com/xoops/html/modules/registry/View.php?ID=232]1955 Packard

jreeder41

Re: Frozen piston

#26

Home away from home

Phew......... You guys had me worried fr a bit.

Posted on: 2010/9/14 11:13

http://www.metropolitan-restoration-service.com/

Stay classy!

PackardV8

Re: Frozen piston

#27

Home away from home

Your worries have only just begun. Pistons and rod bearings for the Packard V8. U're going to find out what worry really is.

Posted on: 2010/9/14 11:39

VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245

Owen_Dyneto

Re: Frozen piston

#28

Forum Ambassador

Geez, don't scare him off! While not the quality Packard used and not what we'd want, plenty of V8 Packards happily touring back and forth w/o problems with Egge pistons and either NOS or NORS undersize rod bearings, or the off-shore reproductions. Those parts have proven adequate for "normal" collector car driving and I'm guessing Jack Vines will support me on that. Are they what you'd like if your going to push the engine aggressively? Probably not.

Posted on: 2010/9/14 12:20

PackardV8

Re: Frozen piston

#29

Home away from home

Well written Owen. Couldn't have said it better myself. Important point for every Packard V8 owner to know. THus any personal judgement calls can made effectively for each individuals efforts based on their demands and expectations of their car .

Posted on: 2010/9/14 13:40

VAPOR LOCK demystified: See paragraph SEVEN of PMCC documentaion as listed in post #11 of the following thread:f
https://packardinfo.com/xoops/html/modules/newbb/viewtopic.php?topic_id=7245