![Bottom Bottom](https://packardinfo.com/xoops/html/modules/newbb/templates/images/icon/down.png)
![Previous Topic Previous Topic](https://packardinfo.com/xoops/html/modules/newbb/templates/images/icon/previous.png)
![Next Topic Next Topic](https://packardinfo.com/xoops/html/modules/newbb/templates/images/icon/next.png)
Re: Wade's Workshop
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Thursday 21st May 2009
Arrived at the workshop to find Wade in discussion with John about the roller rockers. Showing John the differences between the spare rockers and those in Big Red's engine. Reason being Wade had called Egge about 8:00am Sydney time(Approx 4:00pm their time on the 20th) and was informed that they no longer stocked the rollers! Looks like this will necessitate a Plan B along the lines of adapting spare rollers, using stainless washers as spacers and replacing all the "collars" like the ones that came adrift to prevent future problems, although Wade is still wrestling with what to do. I then Metal Readied the parts Marine Cleaned yesterday while Wade Fabrication Industries sprang into action and made 2 gaskets for the Super 8 gear shift. Why two? Because he didn't have one on the '34 and they're the same. Next was putting the trans back into Big Red. Placed the trans on a block of wood(for clearance) on the trolley jack and wheeled it over next to Big Red. Then with John's advice re-balanced it on the jack. With John controlling the jack and Wade in the engine compartment the trans was wheeled into place in front of the position it needs to be. Where was I? Well apart from one quick pic of John in action I was stationed at the open right front door ready to slip bolts into the trans mounts once the holes were aligned. The rubber backed trans mounts were bolted to the trans and this necessitated the trans being raised enough to clear the brackets the mounts bolt to then being slid back on the jack and then lowered into place. Bolt for the right side slipped in easily while those for the left side went in after a bit of jiggling and a few light hammer taps. While I started stringing together a new set of windchimes, aka parts hanging from rack prior to PR-15 painting, Wade was under Big Red bolting the trans cross member back in and installing and tightening the nuts and washers for the trans mounts. I was just about ready to start painting when Wade said that Noel had called earlier and said all the rubber parts he was waiting for should soon be here including new rubber balls for the dog bone. Dog bone? Yes, dog bone, the trans stabiliser mounted to the right side of the trans. Hadn't dis-assembled it so took it apart, cleaned and prepped the pieces and strung it up for POR-15'ing. Painting commenced with me clad in rubber gloves and a long sleeved top for protection. But I was surprised, ![]() ![]() Attach file: ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
Posted on: 2009/5/21 4:18
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: Wade's Workshop
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Friday 22nd May 2009
Wade was busy dis-assembling my latest windchime when I arrived today, this after he's re-installed the newly painted trans stabiliser rod. Finished the dis-assembly by placing the painted parts back in their respective allotted areas. Then the re-built rear shocks and the sway bar were re-installed in Big Red. This operation comprised Wade under Big Red on a creeper and Mal squatting under a rear fender feeding the shock bolts through the chassis. Wade then tightened up the nuts, finishing using a looong bar so they won't come off in a hurry. Next the sway bar went into place but without the necessity for high torque tensioning. Should probably have pumped up each shock individually before the sway bar went in but Wade solved that by doing them together and raised a bit of a sweat doing so. Tony the other day had said he'd be back by the end of the week with the water jacket sideplate cover and true to his word there he was. Looks great, Wade is certainly pleased with it. After Tony left we turned to Big Red's engine as it needed to taken off it's bench and placed on a wheeled wooden trolley. Reason being, Wade's having the cracked fuel pump boss welded up and then will drill and tap the hole again. Hoisted the engine, slid out the bench, it's on wheels, lowered the engine to the ground, then with John's help muscelled it over so it lying on it's right side and presenting the fuel pump boss for easy welding access. Turned then to the partly reamed right king pin bushes and completed that task. Also reamed the right lower supporting arm outer bushes. And was just getting organised to press the king pin into the upright support arm when PACA members Barry and Cheryl arrived. They dropped in a power steering box for PACA member Paul's '54 convertible. Needless to say tools were downed and it wasn't long before lunch was upon us. Barry and Cheryl are accompanying Wade today to experience the workshop's long Friday lunch. Unfortantely I had to pass up this opportunity because of prior commitments. Attach file: ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]()
Posted on: 2009/5/22 1:12
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: Wade's Workshop
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Can't remember specifically for Packard, but burnishing kin pin bushings was a very standard practice, all shops I know of that specialized in front end work did it routinely.
PS - and never use any process that can leave an abrasive (like a wheel cylinder hone) behind, or close the lubricant pockets in the bronze. Ream and burnish is the standard method, burnishing "work-hardens" the surface, I suspect for longer bushing life.
Posted on: 2009/5/22 10:07
|
|||
|
Re: Wade's Workshop
|
||||
---|---|---|---|---|
Home away from home
![]() ![]() ![]() |
Thanks Dave. I was taught never to hone a bushing, always ream it for fitting. I recall my father having many reams, but don't recall any burnishing tools. Probably, my aging memory. Happy holiday weekend.
Posted on: 2009/5/22 14:16
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: Wade's Workshop
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Since most of my other cars have ball-joint type suspension, I'm a bit confused about the need to burnish king pin bushings.
Mind you, I do understand the difference between reaming to remove metal as opposed to burnishing to compact/polish it. Yet, while the 51-54 shop manual specifies reaming undersize, then burnishing to size, including a pic of the tool, the 55-56 shop manual only talks about pressing the bushing - doesn't even mention reaming. As a mechanic, my dad worked on a variety of automobiles, up to and including medium- and heavy-duty trucks, but he only ever talked about reaming king pin bushings - never mentioned burnishing them. More recently, I've read that some front-end kits (in general) are being supplied these days with a warning to NOT hone or burnish the king pin bushings as it will damage them and void the warranty - that they should only be reamed to fit. Perhaps some bushings are of a different material and require different techniques. Any thoughts?
Posted on: 2009/5/22 14:52
|
|||
|
Re: Wade's Workshop
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Recent pic's of Barry's '54 Convertible resto.
EDIT - As it has been made so obvious that it's a '51 and not a '54, see the next four posts, I have retitled the pic's to show the correct year but left my post line intact. ![]()
Posted on: 2009/5/23 2:15
|
|||
Mal
/o[]o\ ==== ![]() Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? ![]() Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: Wade's Workshop
|
||||
---|---|---|---|---|
Just can't stay away
![]() ![]() ![]() |
1954? I assume 1951, with this cormorant, PACKARD spelled on the hood and teeth in the grille.
Tom
Posted on: 2009/5/23 7:49
|
|||
|
Re: Wade's Workshop
|
||||
---|---|---|---|---|
Forum Ambassador
![]() ![]() ![]() |
Can't say I'm a fan of "resale red", but it looks like a lovely restoration on that 51. I shudder to think what the cost was for rechroming the grille!
Posted on: 2009/5/23 8:54
|
|||
|
Re: Wade's Workshop
|
||||
---|---|---|---|---|
Webmaster
![]() ![]() ![]() |
Mal,
Pretty sure that Convertible is not a '54. Wrong grille, side trim, bumper. Also with the fender ventlets, and "Packard" on the hood I would think that is a 51.
Posted on: 2009/5/23 11:15
|
|||
-BigKev
1954 Packard Clipper Deluxe Touring Sedan -> Registry | Project Blog 1937 Packard 115-C Convertible Coupe -> Registry | Project Blog |
||||
|
Register To PostTopic is Locked