Re: Had this problem before, 49 Custom 8 won't go into gear
|
||||
---|---|---|---|---|
Home away from home
|
HH56,
So, I would look at the hoses for swelling or bulging?
Posted on: 2014/11/22 14:29
|
|||
|
Re: Had this problem before, 49 Custom 8 won't go into gear
|
||||
---|---|---|---|---|
Home away from home
|
Good advice from O_D and HH56.
The cap on the front wheel hub (hub cap) pries off, not pushes in - if I read your posting correctly. There are books on basic maintenance and repair, and a parts and repair manual for your Packard is a must. A vintage copy of a"Motors Manual" that covers your year is also a good manual to have. This Packard will also give you the opportunity to purchase a vast collection of hand and power tools. Some you will only use once (usually the most expensive ones). This site has a wealth of information on Packards, and folks here are are always willing to share their knowledge and experiences. (o{}o)
Posted on: 2014/11/22 17:47
|
|||
We move toward
And make happen What occupies our mind... (W. Scherer) |
||||
|
Re: Had this problem before, 49 Custom 8 won't go into gear
|
||||
---|---|---|---|---|
Home away from home
|
I did loosen the star wheel about 15 clicks and that did nothing. But yesterday morning when I first went out there and jacked it up the wheel turned freely. Then when I started it and tried to drive it it went forward a little and froze up again.
Posted on: 2014/11/23 8:51
|
|||
|
Re: Had this problem before, 49 Custom 8 won't go into gear
|
||||
---|---|---|---|---|
Home away from home
|
I am afraid you are going to have to get that drum off and have a look. The last time I experienced something like that, one of the bonded brake linings had fallen off the shoe and was getting jammed.
Posted on: 2014/11/23 10:07
|
|||
|
Re: Had this problem before, 49 Custom 8 won't go into gear
|
||||
---|---|---|---|---|
Forum Ambassador
|
Packard0, if I recall correctly you said you were a bit of a novice on auto service and if you are it's likely you don't have much if anything in the way of specialty tools. If you're in this for the longer haul you may want to invest in a couple of very inexpensive brake tools - yes you can manage without them - but they sure make the job easier.
The first is a tool to remove the grease cup from the front brake drum. The second is a tool to remove and reinstall the brake shoe return springs.
Posted on: 2014/11/23 19:57
|
|||
|
Re: Had this problem before, 49 Custom 8 won't go into gear
|
||||
---|---|---|---|---|
Home away from home
|
Ok, you're right I don't have a bunch of special tools but I do have some tools. I'm determined to get the grease cap off and wheel hub. Give me some tricks to getting the grease cap and hub off without destroying something if you can please. I tried getting the grease cap off with a screwdriver working around it but it didn't appear to do anything. Maybe I should try harder? Also, it's in good condition as it's had regular maintenance so it doesn't appear to be rusted at all.
Posted on: 2014/11/23 21:34
|
|||
|
Re: Had this problem before, 49 Custom 8 won't go into gear
|
||||
---|---|---|---|---|
Forum Ambassador
|
Using a screwdriver to pry the cap off usually works. But, sometimes when the cap is on real hard, something more than "gentle persuasion" is needed. Again use a screwdriver, punch or similar but this time use a hammer to tap the screwdriver, etc against the edge of the cap by working around it to push it off, it'll come.
Edit, if you can find one of those brake spring tools get it!
Posted on: 2014/11/23 21:41
|
|||
Mal
/o[]o\ ==== Bowral, Southern Highlands of NSW, Australia "Out of chaos comes order" - Nietzsche. 1938 Eight Touring Sedan - SOLD 1941 One-Twenty Club Coupe - SOLD 1948 Super Eight Limo, chassis RHD - SOLD 1950 Eight Touring Sedan - SOLD What's this? Put your Packard in the Packard Vehicle Registry! Here's how! Any questions - PM or email me at ozstatman@gmail.com |
||||
|
Re: Had this problem before, 49 Custom 8 won't go into gear
|
||||
---|---|---|---|---|
Forum Ambassador
|
Packard0, if removing the front drum grease cup is what's holding you up, the tool I pictured is quite common and I'd bet you could borrow one from a local brake shop or repair garage, or from a local hobbyist.
Posted on: 2014/11/24 10:20
|
|||
|
Re: Had this problem before, 49 Custom 8 won't go into gear
|
||||
---|---|---|---|---|
Home away from home
|
Here is a pic with grease cap off, it came off super easy and I'm not even going to tell you why it wouldn't come off the first try--stupid me! Now I need to get the wheel hub off right? What's the best way? Oh yeah, I can turn the wheel by hand in the reverse direction but not the forward direction.
Thanks
Posted on: 2014/11/24 11:05
|
|||
|