1948-50 (22nd->23rd Series) - SUSPENSION & STEERING
|
Subject | Application | Document |
Bearings, Care of Ball and Roller installation/removal damage - proper support | (all models) | |
Caster Changed increased - revision to SC Vol. 21, No. 23 | 2220-22 | |
Convertibles on Display, Hold-Down Clamps for clamp springs to simulate load - for showroom use | 2259-79 | |
Directing Acting Shocks - Repair Kit Discontinured Information | (not specified) | |
Flat Rate Manual 1941-49, Changes and Corrections in steering gear | 19th-23rd | |
Flood Zones, Cars in dirt carried in - drain/refill differential, clean/repack wheel bearings | (all models) | |
Front Stabilizer Bearing Brackets, Bent during shipment - inspect, straighten or replace | 22nd | |
Front Stabilizer Service Links new tubular type - eliminates rattles | 1800-1-3-6; 1901-1A-3-3A-4-56-7-8; 2020-1-3; 1951; 2000-01-03-06-10-11; 21st-22nd | |
Front Wheel Bearing Adjustment tightening procedure clarified | 22nd-23rd | |
Front Wheel Bearings - Lubrication Changes reduced quantity of grease | 1951; 2000-01-03-06-10-11; 21st-22nd | |
Rear Spring Rebound Clips two types - identification, replacement | 22nd-23rd | |
Rear Spring Squeaks with insert/liner type - inspection and correction | 22nd | |
Rear Spring U-Bolts, Tightening recheck torque - 1000-mile inspection | (all models) | |
Rear Springs - Parts Men Note part number correction/elimination | 23rd | |
Rear Springs - Save the Grease rubber/Silenite deterioration | 1600-1-2; 1702-3-3A; 18th-22nd | |
Rear Springs, Liner Type new type, interchangeable with insert type - reconditioning | 22nd | |
Rear Springs, New Leaf for Sagging liner type - replaces second leaf | 2201-02; 2301 | |
Rear Springs, Squeaks - Insert Type worn/oxidized inserts - inspection, reconditioning, replacement | 1600-1-2; 1702-3-3A; 18th-22nd | |
Rear Stabilizer Adjustment installation, following removal | 2301 | |
Rear Stabilizer Bar Brackets, Bent insufficient shock absorber clearance - inspect and bend | 2301 | |
Renewing Front Stabilizer Bearings installation procedure | 22nd-23rd | |
Ride, Custom Eight harsh - suspension friction, shock valving or oil | 2306-13-33 | |
Ride, Custom Eight harsh - suspension friction, shock valving or oil | 2306-13-33 | |
Ride, Harsh springs improperly seated - shock absorber valves improperly installed | 22nd | |
Service Manual, Section VI of the Current Chassis section released | 22nd | |
Shock Absorbers - Front and Rear superseded parts - replace in pairs | 22nd-54th | |
Spring Markings, Front End Height and uneven, side-to-side - checks, identification | 23rd | |
Spring Pads, Welding of Rear Axle production change - field inspection, replacement | 23rd | |
Steering Column Shroud, Noise in clicking, creaking - broken spot welds | 22nd | |
Steering Connecting Rod Idler Lever Kit superseded parts, 24th Series type - improved steering, tire life | 1951; 20th-23rd | |
Steering Connecting Rod Idler Lever Kit superseded parts, 24th Series type - improved steering, tire life | 1951; 20th-23rd | |
Steering Cross Bars and Sockets Assemblies interchangeable parts | 22nd-56th | |
Steering Cross Shaft Bushing Replacement Tool Set new special tool - proper placement | 21st-22nd | |
Steering Gear - Lubrication Changes seasonal weight change eliminated | 1951; 2000-01-03-06-10-11; 21st-22nd | |
Steering Knuckle Bearing Shims, Front Wheel superseded parts | 22nd-56th | |
Steering Knuckle Supports superseded parts | 22nd-56th | |
Steering Wheel, Raising - Correction applies to Eights only | 22nd | |
Steering Wheel, Raising install shorter bracket - remove front seat shims | 2201-02; 2301-02 | |
Strike-Through, Front End insufficient riding height - new spacers | 22nd-25th | |
Support Arm Pins and Bushings, Loose proper clearance - other checks and lubrication | 22nd-54th | |
Warning Stickers Discontinued no lubrication of rear leaf springs | 23rd |
SC = Service Counselor | SL = Service Letter | STB = Service Technical Bulletin | SSB = Studebaker Service Bulletin |
NOTE: These PDFs were created from High Quality Scans. It is recommended that you Right Click on the link(s) above and do a "Save Target As". This will download the PDF to your machine rather than trying to open and view it over the web.
Disclosures & Disclaimers
Though previously published elsewhere, this work is provided with my full permission for display on the PackardInfo.com website and the personal use of visitors to that site. Any other unauthorized use, however, is expressly prohibited and may be subject to prosecution.
Also, because this index was compiled from documents published by the factory, neither the author nor PackardInfo.com are responsible for errors in content arising from source information.