1948-50 (22nd->23rd Series) - ENGINE
|
| Subject | Application | Document |
Air Cleaner - see: FUEL & EXHAUST | ||
Bearing Cap Screws, Main new self-locking - omit lock plates | 22nd | |
Bearing Clearance, Main and Rod noise/vibrations - undersize journals, identification | (not specified) | |
Bearing Shells, Note on rod/main bright or dull - no effect | (not specified) | |
Bearings Measured Quickly, Main and Rod new Plastigage Kit - proper use | (not specified) | |
Camshaft superseded part | 23rd; 24th-54th | |
Camshaft, New Type reduces tappet noise, new tappet setting specification - engine suffix E | 2201-02-11-22-32 | |
Camshaft, New Type reduces tappet noise, new tappet setting specification - engine suffix E | 2201-02-11-22-32 | |
Carburetor - see: FUEL & EXHAUST | ||
Compression Ratio, Raising swapping cylinders heads - shaving not recommended | 22nd-23rd | |
Connecting Rod and Crankshaft Identification check length and throw - not interchangeable | 2220-40; 2201-11; 2202-11-22-32 | |
Convertibles, The New new model information - preliminary engine parts list | 2259-79 | |
Crankcase Capacity, Seven-Quart 7-quart oil pan equipment - engine suffix D | 2201-02-11-22-32 | |
Cylinder Head - Part No. 436141 superceding part - thread sealant | 23rd-25th | |
Cylinder Head Studs - New Type rolled threads, reduce water leaks - larger diameter, not interchangeable | 21st-22nd | |
Cylinder Heads - High Compression 288-cid engine - new 7.5:1 design now available | 2201-11; 2301 | |
Cylinder Repairs small holes/cracks - repair compounds | (all models) | |
Distributor - see: ELECTRICAL | ||
Engine and Parts - 288 Cu. In. Displacement universal five-main block and piston assembly - build-up | 22nd-54th | |
Engine and Parts - Five Main Bearing universal block and piston assembly - build-up | 22nd-54th | |
Engine and Parts - Service Bulletin Correction see SSB No. 350, p. 6 - engine/part numbers | 22nd-54th; 55th-56th | |
Engine Idle, Vacuum Type Wipers Affect steps to improve idle quality | 22nd-23rd | |
Engine Installation Precautions protect hydraulic lifters - renew oil filter | 2003-06; 2103-06-26; 2206-13-26-33 | |
Engine Number Suffix Letters designed changes reviewed | 22nd | |
Engine Performance at Low Speed, Poor flat spot, sluggish - new low speed jet tubes, metering rods | 2201-11 | |
Engine Performance at Low Speed, Poor flat spots, sluggish - new metering rods, low speeds jets, identification | 2201-11 | |
Engine Replacement Parts 7-quart oil pan equipment - engine suffix D | 2201-02-11-22-32 | |
Engine Support Bar new special tool - transmission removal | 22nd-23rd | |
Engine Vibration Different Causes of Vibration | (not specified) | |
Engine, Service Replacement - Part Number Correction see SC Vol. 27, No. 9 - fan blade spacer screw | 2003-06; 2103-06-26; 2206-13-26-33; 2313 | |
Engine, Service Replacement - Supplement see SC Vol. 27, No. 7 - additional parts, modifications | 2003-06; 2103-06-26; 2206-13-26-33; 2313 | |
Engine, Service Replacement Custom Eight 356-cid no longer available - 327-cid installation, part number reference | 2003-06; 2103-06-26; 2206-13-26-33; 2313 | |
Engines, Late Type Super Eight - Correction camshaft bearing part number | 2302-22-32 | |
Engines, Late Type Super Eight new hydraulic tappets - related parts | 2302-22-32 | |
Engines, Oversized oversized cylinder bores, new - use of, identification | (all models) | |
Fan Belt - see: RADIATOR & COOLING | ||
Flat Rate Manual 1941-49, Changes and Corrections in select operations | 19th-23rd | |
Flywheel - Application Chart part number reference - incl. converter | 23rd-25th (Ultramatic) | |
Flywheel Attaching Screws (Part Number - Correction) self-locking washers | 23rd-25th (Ultramatic) | |
Flywheel Attaching Screws discard old screw - use new self-locking type | 23rd-25th (Ultramatic) | |
Flywheel, Motor superseded parts - 9- and 11-1/4-in. converters | 23rd-25th (Ultramatic) | |
Generator - see: ELECTRICAL | ||
Heat Control Valve, Manifold - see: FUEL & EXHAUST | -- | -- |
Hydraulic Tappet Checking Tool new special tool - cleaning, testing | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-06-07-08-23-30-55; 2103-06-26; 2206-13-26-33; 2306-13-33 | |
Hydraulic Tappet Gauge Set new special tool - checking valve stem clearance | 2302 | |
Hydraulic Valve Lifter Tester new special tool - checking leak-down | 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8; 2003-04-05-06-07-08-23-30-55; 2103-06-26; 2206-13-26-33; (2306-13-33) | |
Idler Lever Shaft Hole In Replacement Engines not drilled - correction | 2301-2302-2332 (exc. Ultramatic) | |
Ignition - see: ELECTRICAL | ||
Manifold Drain, Intake hard starting, fuel accumulation - production change, field installation | 2206-13-26-33; all prior Super Eights | |
Manifold Gasket Failures chafing - chamfer manifold edges | (all models) | |
Manifold Gasket Leaks, Intake rough idle - improper tightening, detection | (all models) | |
Manifold, Exhaust superceded parts | 22nd-25th | |
Motor Oil New Recommendations | (Not Specified) | |
Motor Support Insulator Retainer Screws, Front loose, broken - new type lockwashers | 2201-02-11-20-22-32-40 | |
Oil Additives, Use of not endorsed - low viscosity, inadequate lubrication | (all models) | |
Oil Capacity, Engine 6 or 7 quart - engine suffix D/E | 2201-02-11-22-32 | |
Oil Consumption, Checking proper method - longer break-in required | 22nd-23rd | |
Oil Consumption, Fuel Pump May Cause High rough idle - fractured booster diaphragm | 22nd-23rd; (24th-54th) | |
Oil Drain Plug Gasket new nylon type | 22nd-56th | |
Oil Filter Cartridge - Change Period Revised high-detergents oils - reduced | 120-138CD; 115C; 16th?-54th | |
Oil Filter Cartridge Change Period Revised high detergent oil - reduced interval | 120-138CD; 115C; 16th?-54th | |
Oil Filter Equipment, Installing accessory - with interval and service part number | 22nd | |
Oil Filter, New Micro Element paper more efficient than cotton waste type | 22nd | |
Oil Filter: Purolator Filter Facts micronic filtration, pleated paper - benefits, replacement period | (not specified) | |
Oil For Sub-Zero Operation, Winter Engine new 5-W oil - issues, limited availability/use | (all models) | |
Oil Level Indicators identification - engine type/suffi | 22nd | |
Oil Pan and Level Indicator - Parts Book Correction application correction - engine suffix | 22nd | |
Oil Pan Gasket Sets replace RH-LH, together - available in sets | 120-138CD; 115C; 1600-1-1A-1D-2; 1700-1-1A-2; 18th-22nd; (23rd54th) | |
Oil Ring Expanders new spring-type adopted - design characteristics | 23rd | |
Oil Seal, Gear Cover burned, leaking - graphite grease | 120-138CD; 115C; 16th-54th | |
Oil Seal, Rear Main Bearing leaks - preventative measures | 120-138CD; 115C; 16th-18th (exc. 1703-3A-5); 1951; 2000-01-03-06-10-11; 21st-24th; (25th-54th) | |
Oil Seal, Rear Main Bearing leaks - undersize | 120-138CD; 115C; 16th-18th (exc. 1703-3A-5); 1951; 2000-01-03-06-10-11; 21st-54th | |
Oil Seal, Rear Main Bearing leaks, bearing distortion - new cork type, installation | 120-138CD; 115C; 16th-18th (exc. 1703-3A-5); 1951; 2000-01-03-06-10-11; 21st-54th | |
Oil Strainer - Parts Book Correction application correction - engine suffix | 22nd | |
Parts for Engine with Suffix Letter F now built with hydraulic tappets - related parts | 2302-22-32 | |
Piston Ring Set - Parts Book Correction application correction - engine suffix | 22nd | |
Pistons And Production Piston Rings new type/suppliers, identification/installation - engine suffix C | 2220-40; 2201-11; 2202-22-32; 2206-13-26-33 | |
Rolled Thread Cylinder Head Stud Tap thread clean-up - new service tool | 22nd | |
-- | -- | |
Service Manual, Sections IV And V of the Current Body, Engine sections released | 22nd | |
Spark Plugs, 14MM new production, torque - part number reference | 23rd | |
Starter - see: ELECTRICAL | ||
Starting - Cold Weather Proper Procedure | (Not Specified) | |
Torque Specifications (Engine), Changes in connecting rod bolt - main bearing cap screw | 22nd | |
Tune-Up Specifications and Adjustments - 1948 tappets | 22nd | |
Valve Guides, Oversize identification by engine suffix - part numbers | 2201-02-11-22-32 | |
Valve Guides, Oversize identification by engine suffix - return excess stock | 2201-02-11-22-32 | |
Valve Seats, Checking run-out, uneven wear - use of dial indicator | (all models) | |
Valve Tappet Clearance new reduced setting - reduces tappet noise | 2201-02-11-22-32 (with Suffix D) | |
Valve Tappet Clearance noise reduction - new specification | 2201-02-11-22-23 | |
Valves, Exhaust - Correction preliminary parts reference - incorrect part number | 22nd | |
Vibration Damper Assembly Kit superseded - modifications | 1900-01-01A; 1951; 2000-01-11; 2100-01-11-30; 2200-11; 2202-22-33; 2220-40; 2302-22-33 | |
Vibration Damper Puller new special tool | 22nd-24th | |
Vibration Damper Pulley hydraulic damper - new tool | 2201-11-20-40 | |
Vibration Damper Replacement new type, not interchangeable - replace timing indicator and fan | 2201-11-20-40 | |
Vibration Damper, New new hydraulic type in production - available for service | 2201-11-20-40 | |
Water Pump - see: RADIATOR & COOLING |
SC = Service Counselor | SL = Service Letter | STB = Service Technical Bulletin | SSB = Studebaker Service Bulletin |
NOTE: These PDFs were created from High Quality Scans. It is recommended that you Right Click on the link(s) above and do a "Save Target As". This will download the PDF to your machine rather than trying to open and view it over the web.
Disclosures & Disclaimers
Though previously published elsewhere, this work is provided with my full permission for display on the PackardInfo.com website and the personal use of visitors to that site. Any other unauthorized use, however, is expressly prohibited and may be subject to prosecution.
Also, because this index was compiled from documents published by the factory, neither the author nor PackardInfo.com are responsible for errors in content arising from source information.
