1937-42 (15th->20th Series) - CLUTCH
|
| Subject | Application | Document |
Chatter, Clutch backing up - fore-to-aft stabilizer (snubber), Junior retrofit | 1600-1 | |
Chatter, Clutch backing up - stabilizer (snubber) reiterated, neutralizing mounts | 1600-1 | |
Chatter, Clutch low, reverse - motor supports, stabilizer (snubber), clutch plate condition | (all models) | |
Chatter, Clutch superseded snubber, 17th Series retrofit - rear spring Silenite inserts | 1600-1 | |
Clutch supplier issues - Borg/Beck, engine suffix identification | 18th | |
Driven Plates, Clutch (Electromatic) different sizes, not interchangeable - parts reference, identification | 1900-1 | |
Electromatic: Adjusting...the Clutch common mistakes - linkage stops, spool rod, body plug | 19th-20th | |
Electromatic: Adjustment engagement characteristics - preferred settings | 19th | |
Electromatic: Aero-Drive Indicator Light on when standing - fuse check | 19th-20th | |
Electromatic: Carburetor Control Linkage Equipment choke, start switch, clutch issues - lost motion, service parts kit (all models) | 20th | |
Electromatic: Carburetor Control Linkage Equipment choke, start switch, clutch issues - lost motion, service parts kit | 20th | |
Electromatic: Clutch Driven Plates different sizes, not interchangeable - parts reference, identification | 1900-1 | |
Electromatic: Clutch Instructions superseded, discard - illustrations renumbered, adjustments/checks revised | 19th | |
Electromatic: Clutch Relay Lever control valve squeak, sticky throwout - relay lever bearing adjustment | 1900-1 | |
Electromatic: Clutch Screw Driver and Wrench new special tool - first/reverse solenoid | 19th | |
Electromatic: Clutch Screw Driver and Wrench redesigned for new taper head screw | 19th | |
Electromatic: Clutch Valve Adjustment erratic performance, sticky spool rod/sleeve - clean, never lubricate | 19th-20th | |
Electromatic: Clutch Valve Adjustment lost motion - install valve linkage spring, clean spool rod | 19th-20th | |
Electromatic: Clutch, Packard... - Owner's Instructions instructions, theory of operation - schematic, adjustments/checks | 19th | |
Electromatic: Disengagement sticking in high gear, decelerating - governor switch | 19th | |
Electromatic: Failure to Release stalling - governor circuit switch checks/adjustments | 19th-20th | |
Electromatic: Mounting...on New Cylinder Head support holes not drilled - layout, specifications | 1901 | |
Electromatic: No-Rol, ...and incompatibilities - not recommended together | 19th | |
Electromatic: Red Pedal Pads back in stock - easy equipment identification | 19th-21st | |
Electromatic: Wiring constant battery drain - governor/ignition switch wires | 19th | |
Electromatic: Wiring Diagram, Clutch new model information - Other Models | 20th (exc. 2000-01-03-06-10-11) | |
Finger Adjustment Dimensions, Clutch reference - special tool | 120-138CD; 115C; 15th-20th | |
Flat Rate Manual 1941-49, Changes and Corrections in clutch pedal booster spring | 19th-23rd | |
Flywheel Housing Clutch Shifter Relay Pivot Puller new special tool - due to clutch relay lever change | 1600-1-2 | |
History Correction, Clutch substitution of Long driven plate - not pressure plate | 18th | |
History, Clutch driven/pressure plate suppliers - not interchangeable, part reference | 18th | |
Linkage, Clutch lost motion, disengagement - linkage wear, use of 1900-01 parts | 1600-1; 1700-1; 1800-1 | |
Linkage, Clutch squeaks rattles, clutch relay lever - washers/springs added, retrofit | 1600-1-2 | |
No-Rol Installation control valve clutch lever modification - drawing | 1900-1 | |
Oil on Clutch Hubs, rear main bearing return leak - oil pan stud, copper washers | 18th | |
Pedal Adjustment, Clutch high pedal pressure, Borg/Beck - assist spring adjustment | 18th | |
Pedal Adjustment, Clutch slippage, sticking in gear - free play | (all models) | |
Plate Aligning and Riveting Fixtures, Clutch new tools - proper use | (not specified) | |
Plate Aligning Fixture Expansion Arbor, Clutch new special tool - updates existing arbor | 1703 | |
Plates, Clutch higher friction lag driven plate for Aero-Drive - identification | 1800-1; 1900-1 | |
Pressure Spring, Clutch part reference - identification | 7th-20th | |
Relay Lever Pins, Clutch working loose, booster mechanism - new design pin | 1703-3A-5; 1803-3A-4-5-6-7-8; 1800-1-1A (w/ Borg&Beck) | |
Relay Lever, Clutch (Electromatic) control valve squeak, sticky throwout - relay lever bearing adjustment | 1900-1 | |
Relay Lever, Clutch - Extra Lubrication Point Super Eight or Borg-Beck equipment - identification | 18th | |
Relay Lever, Clutch - Super Eight centralizing springs - additional washers | 1703-3A-5; 1803-3A-4-5-6-7-8; 1903-3A-4-5-6-7-8 | |
Shop Manual Corrections (1938-1939) clutch relay lever lubrication - Super Eight, 1939 only | 1703-3A-5 |
SC = Service Counselor | SL = Service Letter | STB = Service Technical Bulletin | SSB = Studebaker Service Bulletin |
NOTE: These PDFs were created from High Quality Scans. It is recommended that you Right Click on the link(s) above and do a "Save Target As". This will download the PDF to your machine rather than trying to open and view it over the web.
Disclosures & Disclaimers
Though previously published elsewhere, this work is provided with my full permission for display on the PackardInfo.com website and the personal use of visitors to that site. Any other unauthorized use, however, is expressly prohibited and may be subject to prosecution.
Also, because this index was compiled from documents published by the factory, neither the author nor PackardInfo.com are responsible for errors in content arising from source information.
